manualshive.com logo in svg

Asahi/America 94 Series, Installation, Operation And Maintenance Manual

Share
Download
Asahi/America 94 Series Installation, Operation And Maintenance Manual Download Page 21

ASAHI/AMERICA, INC  655 ANDOVER STREET  LAWRENCE, MA. 01843    TELEPHONE 800-343-3618 

File:  assembly/manuals/Series 94 Gen II A/C Modulating Svc Manual           Rev. A 

11/19/19  

Page 21 of 27 

Option Modules 

 
Various option modules can be plugged into the DHC-100 option module 
connector, J3.  Option modules provide additional features such as position 
feedback signals, auxiliary switch outputs, or digital communications.  Contact the 
factory for the latest available modules.  Refer to the diagram below for 
instructions on installing an option module. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Installing an Option Module

Loosen front panel screws and lift
front panel up to allow option
module to plug in underneath.

Plug option module into J3,
lock module in front panel
slots, and retighten front
panel screws.

DHC-100

Option

Module

J3

Summary of Contents for 94 Series



































Reviews:

No comments

Brands by name

Popular brands

Load more brands