manualshive.com logo in svg

ARTEX 570-2225, Manual, Page: 5 / 33

Share
Download
ARTEX 570-2225 Manual Download Page 5

1  

Hardware and Software Package 

 

131-0009 9 Volt Batteries 

 

500-0232 RS-232 Level Shifter 

 

500-8000 PA-PI, Modified 

 

510-0406 CD-ROM Disk 

 

570-2225 Repair Station Manual for 406 MHz ELT Programming 

 

571-0017 Battery Replacement  Instructions 

 

611-0099 ME406 Programming Adapter 

 

1600 “Temporary” 24 Bit Address Assignment Form

 

 

6178 Country Code List

 

 

Note:  A 406 MHz Beacon Tester is not included in this package but is necessary to 
test newly programmed ELT’s. Either the Sartech ARG 5410 (Artex P/N 453-0131 
available in Kits 455-9010-01, 455-9010-02, 455-9010-03 or 455-9010-04) w/ coax, 
and attenuator or Artex ETS (Artex P/N 453-1000 available in Kit 455-9100) or an 
equivalent test set may be used. Contact the Artex Sales department for details and 
current availability. 

 

Note: A 121.5 MHz receiver is not included in this package but is necessary to 
monitor ELT’s during programming. 

2  Computer Requirements 

 

The 510-0406 programming software requires an IBM-compatible PC with a Microsoft 
Windows 95™ or newer operating system installed. 

 

The PC should have a keyboard, mouse, color monitor, and CD-ROM. 

 

The PC should have 10 megabytes of HD space free and available. 

 

The PC should have a local or network printer available.  A local printer not configured 
through Windows 95™ must be installed on LPT1 or LPT2. 

 

The PC should have one available 9-pin male serial (COM) port on the host computer.  
If a 9 pin male serial port is not available, a 25 pin male serial port may be used with a 
25-pin female-to-9 pin male adapter.  The programming software requires that the serial 
port used be either COM1 or COM2. 

3  System Installation / Removal 

3.1  Level shifter installation 

 

If batteries are not installed, install batteries or attach external power supply that matches 
ratings on Level Shifter label. Close case. 

 

With the host computer off, plug Level Shifter 9 pin female connector into the host 
computer’s COM1 or COM2 serial port.  Use a 25-pin female-to-9 pin male adapter if 
the only available port is the 25 pin male type.  Do not confuse a 25 pin male serial port 
with a 25-pin female printer port. 

  

Page 

1 

 

Summary of Contents for 570-2225


































Reviews:

No comments