Artesyn PmPPC440 User Manual Download

Page: 66 / 99

7-10

PmPPC440: Development Mezzanine Card

April 2005

7.3 DMC Jumpers

There are a total of five jumper pairs on the DMC. Pins 9 and 10 are spare jumper
posts. See Fig. 7-1 for the jumper location on the DMC.

Figure 7-7. DMC Jumper Pin Assignments, JP1

7.3.1 Jumper Setting Register

These read-only bits may be read by software at location C100,0028

to deter-

mine the current DMC jumper (JP1) settings.

JP1

This is a user-defined jumper.

JP2

JP2 (pins 3 and 4) selects the 8-bit ROM socket as the boot device. In
order for the socket to provide boot code, the DMC must be seated on
the PmPPC440 and the boot jumper must be in place.

JP3

This is a user-defined jumper.

JP4

JP4 is the PPC440GP serial ROM configuration jumper. If JP4 is installed,
the PPC440GP will not try to configure from the serial ROM.

Reserved

JP4

JP3

JP2

JP1

Register Map 7-1. DMC Jumper

ARE

User-Defined (JP1) BOOT User-Defined (JP3) ROM Config. (JP4)

(JP2)

Summary of Contents for PmPPC440




































































































Search results

Summary of Contents for PmPPC440

Reviews:

Related manuals for PmPPC440

Brands by name

Popular brands

Artesyn PmPPC440, User Manual

Search results

Summary of Contents for PmPPC440

Reviews:

Related manuals for PmPPC440

Brands by name

Popular brands