manualshive.com logo in svg

Artesyn PmPPC440, User Manual

Share
Download
Artesyn PmPPC440 User Manual Download Page 29

Resets

2-9

10003794-05

2.4   Resets

The PmPPC440 has several sources for resets. The power-on sequence, the front 
panel reset switch, and a PCI reset all perform a hard reset to the entire board. 
Also, a software-controlled Reset Command register at C100,0008

16

 allows for 

various types of resets, as follows:

After being written to, the Reset Command register bits clear automatically. The 
Hard Reset Command is disabled if the QS_QE bit is active (see Register Map 2-2). 
When the PCI Reset Command is active, it prevents a PCI reset from affecting the 
board.

The Quick Switch Enable register at C100,0034

16

 provides for two reset modes. 

When bit zero is active (enabled), the PCI Reset signal connects to the PPC440GP 
processor’s SYS_RESET pin. When this bit is not active (disabled), the PmPPC440’s 
programmable logic device (PLD) drives the SYS_RESET pin. The reset value for 
the QS_QE bit is one (enabled).

3

2

1

0

PCI

Ethernet

Flash

Hard

Register Map 2-1. Configuration Command

PCI

PCI Reset Command. Writing a one to this bit asserts the ResetOut signal 
on the PCI interface. The reset value is zero.

Ethernet

Ethernet Reset Command. Writing a one to this bit causes an Ethernet 
reset. The reset value is zero.

Flash

Flash Reset Command. Writing a one to this bit causes a Flash reset. The 
reset value is zero.

Hard

Hard Reset Command. Writing a one to this bit causes a hard reset to the 
board. The reset value is zero.

3

2

1

0

reserved

QS_QE

Register Map 2-2. Quick Switch Enable

Summary of Contents for PmPPC440




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands