Arrow CYC1000 User Manual Download Page 17

Page: 17 / 66

CYC1000 User Guide

www.arrow.com

Page | 17

January 2020

3.3.8

User I/O

The CYC1000 board has two additional pins that can be connected to the board and take GPIOs.

Board Reference

FPGA Pin No.

Description

I/O Standard

AIN

PIN_T12

GPIO

3.3 V

AIN7

PIN_R11

GPIO

3.3 V

GND

N/A

Ground

N/A

3.3.9

Communication and Configuration

The CYC1000 board uses a single chip to perform configuration of the device and USB to UART
communications, having each described below.

3.3.9.1

UART Communication

UART to USB communication supports USB 2.0 High Speed (up to 480 Mb/s) independently of
other protocols used in the chip like JTAG. Below is the connection schematic and pinning
information.

Board Reference

FPGA Pin No.

Description

I/O Standard

BDBUS0

PIN_R7

Transmitter output of FT2232H (Tx)

3.3 V

BDBUS1

PIN_T7

Receiver input of FT2232H (Rx)

3.3 V

BDBUS2

PIN_R6

Ready To Send handshake output (RTS)

3.3 V

BDBUS3

PIN_T6

Clear To Send handshake input (CTS)

3.3 V

BDBUS4

PIN_R5

Data Transmit Ready (DTR)

3.3 V

BDBUS5

PIN_T5

Data Set Ready (DSR)

3.3 V

Figure 12 - User I/O Connections

Figure 13

–

UART Connections

Summary of Contents for CYC1000



































































Search results

Summary of Contents for CYC1000

Reviews:

Related manuals for CYC1000

Brands by name

Popular brands

Arrow CYC1000, User Manual

Search results

Summary of Contents for CYC1000

Reviews:

Related manuals for CYC1000

Brands by name

Popular brands