ARRI TRINITY 2 Quick Manual Download Page 13 | Manualshive

Page: 13 / 23

background image

TRINITY 2 balance quick guide

13

3

TRINITY 2 balance quick guide

Center the Top Stage

Adjust Side to Side
► Turn the side to side adjustment until the top stage is left and right

in the center.

Or until the edges of the housing are aligned.

Adjust Fore and Aft
► Turn the fore and aft adjustment until the top stage is front and

back / left in the center.

There should be equal spacing at both ends.

Center the Pendulum

Adjust the Pendulum
► Turn the side to side adjustment until the center

column of the pendulum is

centered left and right

.

Center the Post

Adjust the Post Fine Trim
► Turn the fine trim adjustment until there is about 10mm / 0.4in

clearance.

«
...
11
12
13
14
15
...
»

Summary of Contents for TRINITY 2
























Reviews:

No comments

Related manuals for TRINITY 2

SECURICAM Network DCS-900

Brand: D-Link Pages: 20

SECURICAM Network DCS-2120

Brand: D-Link Pages: 25

DCS-6620G - Network Camera

Brand: D-Link Pages: 16

Brand: D-Link Pages: 7

Brand: D-Link Pages: 24

WIRELESS G DCS-950G

Brand: D-Link Pages: 2

Versaflo M Series

Brand: 3M Pages: 27

Speedglas 9100 Series

Brand: 3M Pages: 64

Speedglas 9100 Series

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Speedglas 9002NC

Brand: 3M Pages: 52

Brand: 3M Pages: 5

Speedglas 9100 FX Series

Brand: 3M Pages: 2

Brand: Quincy lab Pages: 4

Brand: Can-Am Pages: 16

Brand: Hama Pages: 10

Brand: Targus Pages: 4

Brand: Targus Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands