manualshive.com logo in svg

ARRI TRINITY 2, Quick Manual

Share
Download
ARRI TRINITY 2 Quick Manual Download Page 9

TRINITY 2 camera setup quick guide

9

Secure component and accessory attachment

ADVICE

Make sure that all components of the camera and accessories in the setup are fully tightened. 

Ensure that none of the components are loose or have any play to avoid vibration and any

performance issues.

Camera Dovetail Plates

Using the SAM plates will speed up the camera setup and later the balancing

process.

The special hight of every SAM plate will lift the dedicated camera right into the

center of the TRINITY 2 inner ring. 

This way a perfect COG of the camera is guaranteed.

Available SAM plates and lens support brackets:

K2.0041201

Stabilizer Adapter Mount SAM-Zero

K2.0018851

Stabilizer Adapter Mount SAM-1 for ALEXA

K2.0014215

Stabilizer Adapter Mount SAM-2 for ALEXA

KK.0016116

Stabilizer Adapter Mount SAM-2 Set for ALEXA Mini

K2.0014630

Stabilizer Adapter Mount SAM-3 Set for AMIRA

K2.0024508

Stabilizer Adapter Mount SAM-6

K2.0039405

Stabilizer Adapter Mount SAM-6 450mm/18in

K2.0034512

CSS Broadcast Dovetail Plate (SAM plate standard width)

K2.0039803

Stabilizer Plate for CBP 355mm/14in

K2.0038536

Stabilizer Plate for CBP 450mm/18in

K2.0033662

Stabilizer Adapter Mount SAM-4

KK.0038971

Long Stabilizer Mount 15mm Mini/Mini

KK.0038972

Long Stabilizer Mount 19mm Mini/Mini LF

K2.0039089

Compact Lens Support CLS-1

K2.0040036

Balance Utility Dovetail BUD-2

K2.0039861

Dovetail Utility Base DUB-1

K2.0038537

Stabilizer System Bracket SSB-2 19mm

K2.0038618

Stabilizer System Bracket SSB-2 15mm

Summary of Contents for TRINITY 2
























Reviews:

No comments

Brands by name

Popular brands

Load more brands