ARRI TRINITY 2 Quick Manual Download | Manualshive

Page: 17 / 23

background image

TRINITY 2 balance quick guide

17

Power up the TRINITY 2 Stabilization

CAUTION

Automatically move to the home position

Risk of crushing fingers. The camera / tilt and roll axis will automatically move to the home

position, after turning on the stabilization.

Make sure that your fingers do not get between the top cover and the camera while checking the

tilt axis.

Stabilizer ON

► Turn the

Stabilizer ON

, when the camera preparation is complete.

Global Home Position / Display

►

Home

is displayed in the small display.

►

Press

the

Jog-Wheel

to move the Tilt and Roll axis in

the

neutral Home position.

► Observe that the TILT and ROLL axis have automatical-

ly moved to the global / absolute zero position.

«
...
15
16
17
18
19
...
»

Summary of Contents for TRINITY 2
























Reviews:

No comments

Related manuals for TRINITY 2

Brand: Manfrotto Pages: 2

Brand: Garmin Pages: 26

Brand: Garmin Pages: 33

Brand: Garmin Pages: 167

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: e-conolight Pages: 3

Brand: E+E Elektronik Pages: 16

Brand: E+E Elektronik Pages: 14

Brand: E+E Elektronik Pages: 22

Brand: E+E Elektronik Pages: 16

Brand: E+E Elektronik Pages: 16

Brand: Laser Pages: 8

Brand: Razor Pages: 2

RAZORX LONGBOARD

Brand: Razor Pages: 16

Brand: RayTek Pages: 93

1306 RAPID SYSTEM

Brand: Thule Pages: 8

Brand: Woody Valley Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands