ARISTEL NETWORKS
PTY. LTD
Models: Q1 or later, ARB2, ARB3, ARB4 (GSM) & NEOS 3000A-3G ARB4 Manual
Ver. 1.4 Nov 2009
page 5
Connected as an exchange line on a Telephone System
Select the exchange line connected to the NEOS3000 (Manual or Auto LCR)
Listen for dial tone. (Check system connections if no dial tone is heard)
Dial the desired number
NOTE! If using a system, the NEOS3000 can be left in the default condition. No
programming is required
Entering programming mode
Plug a telephone (SLT) into the “PHONE” socket and unplug the “LINE” connection, Lift off the
handset. You will hear continuous dial tone. Dial * * * * #. You will hear “Beep, Beep, Beep”
repeated continuously. The green and yellow LEDs flash. You have 8 seconds to enter the password.
Enter the password (default = 1234#) you will hear a “Der” tone (this is “set-up” tone) repeated
every 2 seconds. The green and the yellow LEDs will slow flash.
System programming can now be commenced. See chart below. If a feature is correctly programmed,
the green and the yellow LEDs will flash once and a Beep tone will be heard. If the input was
incorrect, the green and the yellow LEDs will flash three times and three Beep tones will be heard. If
you make an incorrect entry, hang up for less than 2 sec. to return to set-up mode To end
programming, hang-up for more than 2 sec. or press * * 0 0 #
Programming Features
Factory Default Settings -
Press 9 9 9 to reset the unit back to Factory Default Settings
Feature
Function Code
Description
Setup Mode
＊＊＊＊＃
Enter the setup mode from the normal mode.
Pick up the phone handset and you will hear the dial tone. Press
『
＊＊＊＊＃
』
to enter setup
mode. Press the engineer password to enter the programming mode in 8 seconds.
Otherwise it will escape the setup mode and return to the normal mode.
＊＊００＃
Escape the programming mode and return to the normal mode.
When programming is finished please press
『
＊＊００＃
』
to escape the setup mode and you
will hear the dial tone and return to the normal mode.
SECRET
Original manufacture password. You can use the original password to enter programming
mode if you lose the engineer password.
Password
０ＸＸＸＸＸＸＸＸ＃
Set the engineer password. It is 4 to 8 digits not including #. The default is
『
１２３４
#
』
.
Example: Set
０
８７６５４３２１＃
, the password becomes
８７６５４３２１
#
from
１２３４
#
.
９１３
To disable press the engineer password.
Don’t press the engineer password after pressing
『
＊＊＊＊
＃
』
to enter programming mode
directly.
９１４
To enable press the engineer password.
You need to press the engineer password after pressing
『
＊＊＊＊
＃
』
to enter programming
mode.
Permissible
Dialling
９１５
Disable the limited dial of a permissible dialling number. It is the default.
You can make any call from a mobile trunk limitlessly and the routing function deactivates.
９１６
Enable the limited dial of permissible dialling number.
You can only call through a mobile trunk when the prefix of a number matches the
permissible dial number without a PSTN line.
Routing function: The matched numbers are called through a mobile trunk and other
numbers are called through PSTN.
８０ＸＸＸＸ＃
Add the new permissible dialling number (without PSTN line) and routing number (with PSTN
line).
The permissible dialling number is 1 to 4 digits and up to 50 sets.
Example: Set
８０
０９
１２＃
. T
he numbers of 0912xxxxxx go through a mobile trunk, the other
numbers go through PSTN.
７０ＸＸＸＸ＃
Delete the saved permissible dialling number (without PSTN line) and routing number (with
PSTN line).
９９８
Delete all the saved permissible dialling numbers (without PSTN line) and routing numbers
(with PSTN line).
Limit dialling
from PSTN
８１ＸＸＸＸ＃
Add the new limit dialling number from PSTN line.
The limit dialling number is 1 to 4 digits and up to 20 sets.
Example: Set
８1
０２０４
＃
. T
he numbers of 0204xxxxxx can not call through PSTN.
７１ＸＸＸＸ＃
Delete the saved limit dialling number from PSTN line.
９９７
Delete all the saved limit dialling numbers from PSTN line.
