Aristel AV SERIES Programming Manual Download Page 56 | Manualshive

Page: 56 / 67

background image

Revised by R. Robinson

Issue AV1.13 8 June 2006

53

Zone 505

Station Function 2

(Ext: = Extension number)

Default value =

1 1 1 0 1 1 0 0

Range =

N/A

This Zone allows the programmer to set the station parameters as listed below:
Item 01: Paging

External and Internal Paging Facility

This allows or disallows the Paging facility for the station.
0 = Disable
1 = Enable
Default = 1
Related Zones.

Item 02: Be Paged

Allows this station to be included in the paging function.

This station can be included or excluded from paging calls by other stations.
0 = Disable
1 = Enable
Default = 1
Related Zones.

Item 03:Hold Func

Hold a Call function.

This enables or disables the ability for a station to place a call in Hold
0 = Disable Hold

1 = Enable Hold

Disable is recommended for Hotel/Motel SLT exts. To prevent switch-hook flash on hangup
Default = 1
Related Zones.

None

Item 04:Manual

Direct link to Operator.

Allows or disallows the following function. By lifting the hand-piece or pressing the Spk key, the station will
automatically make an intercom call to the operator console set in

, Group 1, Item 1. (Main Console)

0 = Disable
1 = Enable
Default = 0
Related Zones.

,

Item 05:Call Split

Alternate call function

(See the System Administrator Manual for Conference Call Operation.)

Alternate call operation for 2

nd

call incoming.

Alternate call operation for 2

nd

call outgoing.

1)

Place the first call on hold

1) Place the first call on hold

2)

Go On-Hook

2) Seize a free CO Line

3)

Wait for the second call to ring the phone

3) Dial the wanted number

4)

Answer the second call

4) Use Flash button to alternate between calls

5)

Use Flash button to alternate between the calls.

0 = Disable

NOTE! Must be 1 if conferencing for SLTs is required

1 = Enable
Related Zones.

Item 06:Sys Alarm

System Alarm signaling at a station.

This allows or disallows the station to be signaled when the System Alarm has been triggered and when the
Alarm time in

has been reached.

Related Zones.

,

Item 07: Alarm Sig

Signal to be used by System Alarm.

This sets the System Alarm to use either Do Not Disturb tone (1) or Background Music (0) as the Signal.

Related Zones.

,

Item 08: Security

Locking/ Unlocking of stations for outgoing calls.

This allows any station (Keyphone or SLT) to be locked (barred) to common allowed codes only for outgoing
calls. The station can only dial CAC numbers until it is unlocked. This is important for Hotel/Motel guest exts.
Related Zones.

«
...
54
55
56
57
58
...
»

Summary of Contents for AV SERIES




































































Reviews:

No comments

Related manuals for AV SERIES

Brand: Samsung Pages: 68

Brand: Samsung Pages: 89

Brand: Samsung Pages: 72

Brand: Samsung Pages: 59

Brand: Samsung Pages: 42

Brand: Samsung Pages: 15

Brand: RAKINDA Pages: 20

Brand: Yealink Pages: 48

Brand: Yealink Pages: 2

T46S Skype for Business

Brand: Yealink Pages: 3

Brand: YAKOYA Pages: 25

Brand: TRIGA Pages: 33

80-6113-00 - AT&T E5812B - 5.8 GHz Dual Handset Answering System

Brand: VTech Pages: 50

Brand: Sagem Pages: 2

Brand: Uniden Pages: 55

Brand: Tempo Fitness Pages: 6

Brand: Clas Ohlson Pages: 2

Brand: Aastra Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands