Arcus PMX-4EX-SA User Manual Download

Page: 87 / 97

PMX-4EX-SA Manual

page 87

Rev 3.11

DO[1-8]

R/W

Set/get individual bit status of digital
outputs. Range for the bit assigned digital
outputs is [0,1].

DO2=1 ;Turn on DO2

ECLEAR[axis]

Clear any motor status errors.

ECLEARX

R/W

Set/get the enable output status. Refer to
Table 6.1

EO=3 ;Enable the X and Y motor

EO[1-4]

R/W

Set/get individual bit status of the enable
outputs.

EO3=1 ;Enable the Z motor

E[axis]

R/W

Set/get the current encoder position.

EX=1000 ;Set to X enc to 1000
V1=EU ;Read current U encoder

GOSUB [0-31]

Call a subroutine that has been previously
stored to flash memory.

GOSUB 0
END

HLHOME[axis][+/-]

Home the motor using the home input at
low and high speeds in the specified
direction. See section 6.13.5 for details.

;positive X home
WAITX ;wait for X home move

HOME[axis][+/-]

Home the motor using the home input at
high speed in specified direction. See
section 6.13.1 for details.

HOMEX- ;negative X home
WAITX ;wait for X home move

HSPD

R/W

Set/get the global high speed setting. Unit
is in pulses/second.

HSPD=1000
HSPD=V1

HSPD[axis]

R/W

Set/get the individual high speed setting.
Unit is in pulses/second.

HSPDY=1000
HSPDZ=V1

IF
ELSEIF
ELSE
ENDIF

Perform a standard IF/ELSEIF/ELSE
conditional. Any command with read
ability can be used in a conditional.

ENDIF should be used to close off an IF
statement.

Conditions [=, >, <, >=, <=, !=] are
available

IF DI1=0
  DO=1 ;Turn on DO1
ELSEIF DI2=0
  DO=2; Turn on DO2
ELSE
  DO=0; Turn off DO
ENDIF

INC

Set the move mode to incremental mode.

INC
X1000 ;increment by 1000

JOG[axis][+/-]

Move the motor indefinitely in the
specified direction.

JOGX+

JOYENA

Set the joystick enable setting. See
section 6.20 for details.

JOYENA=3 ;enable joystick X,Y

JOYHS[axis]

Set the high speed setting for joystick
control. See section 6.20 for details.

JOYHSX=2000
JOYHSZ=5000

JOYDEL[axis]

Set the speed change delta for joystick
control. See section 6.20 for details.

JOYDELZ=100
JOYDELU=200

LHOME[axis][+/-]

Home the motor using the limit inputs in
the specified directions. See section
6.13.2 for details.

;positive home
WAITX

LSPD

R/W

Set/get the global low speed setting. Unit
is in pulses/second.

LSPD=100
LSPD=V3

LSPD[axis]

R/W

Set/get the individual low speed setting.
Unit is in pulses/second.

LSPDX=100
LSPDY=V1

MST[axis]

Get the current motor status of the motor
of an axis. See Table 6.2 for motor status
assignment.

PRG [0-3]
END

Used to define the beginning and end of a
main program. Four standalone programs
are available

PRG 0
;main program
END

Summary of Contents for PMX-4EX-SA


































































































Search results

Summary of Contents for PMX-4EX-SA

Reviews:

Related manuals for PMX-4EX-SA

Brands by name

Popular brands

Arcus PMX-4EX-SA, User Manual

Search results

Summary of Contents for PMX-4EX-SA

Reviews:

Related manuals for PMX-4EX-SA

Brands by name

Popular brands