background image

10

GENERAL INFORMATION

INDICATOR LIGHTS (Standard 
Models)

Indicator lights are incorporated

within the speedometer.

LOW OIL WARNING LIGHT
(Standard 2-Stroke Models)

The Low Oil Warning Light is

designed to alert the snowmobile

operator when the oil in the oil injec-

tion reservoir gets below a pre-

scribed level; however, it is highly

recommended that a visual verifica-

tion of the oil level in the reservoir

be done prior to operating the snow-

mobile. Once the Low Oil Warning

Light illuminates during operation

of the snowmobile, the operator

must periodically monitor the level

of oil in the reservoir and must fill

the reservoir the next time gasoline

is added to the gas tank. The “alert

level” of the Low Oil Warning Light

is approximately equal to 1 tankful

of gasoline under normal operating

conditions.

LOW OIL PRESSURE WARNING 
LIGHT (660 cc Models)

The Low Oil Pressure Warning

Light indicates engine oil pressure,

not the oil level; however, if the oil

level is low, it may affect oil pres-

sure. The light should illuminate

each time the ignition switch is

turned to RUN or START, and it

should go out when the engine

starts. If the light illuminates while

the engine is running, oil pressure

has been lost and the engine will

automatically shut off. 
If oil pressure is lost, use the follow-

ing procedure:

1. Check the oil level.

 NOTE: To ensure an accurate

reading, the snowmobile should
be on level ground.

2. If the oil level is below the

lower mark on the oil level

stick, add only enough recom-

mended oil to raise the level

between the upper and lower

marks. DO NOT overfill the

crankcase with oil.

3. After adding oil if the engine

starts, oil pressure should be

normal. 

If the engine does not start, take the

snowmobile to an authorized Arctic

Cat Snowmobile dealer.

HIGH TEMPERATURE 
WARNING LIGHT                
(Standard Liquid Cooled 
Models)

The High Temperature Warning

Light is designed to alert the snow-

mobile operator when the tempera-

ture of the engine coolant exceeds a

safe operating temperature. If the

High Temperature Warning Light

illuminates during operation of the

snowmobile, immediately shut off

the engine and determine the nature

of the problem (low coolant level,

etc.). If unable to either determine or

remedy the problem, take the snow-

mobile to an authorized Arctic Cat

Snowmobile dealer for service. If

not under warranty, this service is at

the discretion and expense of the

snowmobile owner.

 NOTE: Operating the snowmo-

bile at slow speed over minimal
snow or hard pack terrain may
c aus e exces sive  engine heat
build-up. If the High Temperature
Warning Light illuminates under
these conditions, immediately
change to a loose snow terrain.

Summary of Contents for Z Series 2006

























































































Reviews: