manualshive.com logo in svg

ARCBRO Stinger Series, User Manual, Page: 73 / 77

Share
Download
ARCBRO Stinger Series User Manual Download Page 73

Service Support Spirit                 

 

 

 

Unique Solution                                    

  WWW.ARCBRO.COM

 

 

73 

Appendix I: Instructions for Software Upgrading Operation 

Functions:   
    The system software is allowed to upgrade through an USB disk.   
The specific operation procedure is as follows:   
1.File upgrading 

Copy the upgrading file titled STARTCNC.EXE to an USB disk.   

2.Operation procedure 

Push and hold the button between 

the red button 0 and the USB port.   

 

Power the system on and release the button when upgrading window appears on the 

display screen. Plug the USB disk into the port and press Key F1 under the display screen(the 
key corresponds to "UPGRADE" in the menu displayed). The system will automatically start 
upgrading operation.   
3.Upgrading end 

If program upgrading is successful, the system will prompt "Upgraded Successfully" and 

sound one beep. If program upgrading fails, the system will prompt "Upgrade Failure" and 
sound continuous beeps. 

。

 

4.New program startup 

Power the system off and unplug the USB disk. Reboot the system to start up the upgraded 

program. The version number of the upgraded program will appear on the screen after booted 
up.   

Notes:   

Please make the following check if upgrading operation fails.   
1) The USB disk must be FAT or FAT32 format. FAT format is preferable.   
2) The upgrading file must be titled as STARTCNC.EXE.   
3) If no prompt appears in the upgrading process and the display returns to the main upgrading 
window or upgrading operation fails due to any other interruption,  verify first the name of 
upgrading file and the format of USB disk. If these two factors are assured, try to upgrade the 
program again following the specific operation procedure.   
 
 

Summary of Contents for Stinger Series














































































Reviews:

No comments