manualshive.com logo in svg

ARCBRO Stinger Series, User Manual, Page: 48 / 77

Share
Download
ARCBRO Stinger Series User Manual Download Page 48

Service Support Spirit                 

 

 

 

Unique Solution                                    

  WWW.ARCBRO.COM

 

 

48 

G40 the end mark of cutter compensation, a G00 command is necessary to adjust the position 
back.   

6.4. M Auxiliary Commands 

M00       Program suspension command. The program execution will be suspended at this 
command until [START] key is pressed.   
M02       Program end command. The program will be pended at this command.   
M30       The same as M02.   
M10/M11  Acetylene(GAS) valve switch commands, M10 to open and M11 to close the valve.   
M12/M13  Cutting oxygen valve switch commands, M12 to open and M13 to close the valve.   
M14/M15  Cutting torch lift switch commands, M14 to turn on and M15 to turn off.   
M16/M17  Cutting torch lower switch commands, M16 to turn on and M17 to turn off.   
M24/M25  Reserved switch commands, M24 to turn on and M25 to turn off.   
M20/M21    Ignition switch commands, M20 to turn on and M21 to turn off.   
M07      Fixed loop of piercing(M07 allows to relocate the cutting torch, but impossible to 
return) 
M08      Fixed loop of cutting stop 
The operation sequence of M07 in flame cutting operation is as follows:   
Open acetylene(gas) valve and ignite the torch if the valve is not open.   
Lower the cutting torch(for time delay of torch lowering, see M71 command);   

Open the oxygen preheating valve and count preheating time delay. If the preheating time 

is insufficient, it will be prolonged to 150 seconds automatically by pressing [PAUSE] key. If 
preheating is done in the midway,  press [START] key to abort the time delay. The new 
preheating time will be automatically saved in the parameter of preheating time delay.   
Lift the cutting torch(and count the time delay of lifting torch, M72);   

Open the cutting oxygen valve(M12), count the time delay and lower the cutting torch(count 

the time delay of lowering torch , M73).   
Switch on height controller(M38) and run the subsequent program.   
The operation sequence of M07 in plasma cutting operation is as follows: 

Lower the cutting torch(and count the time delay of lowering torch, see M71);   

If hole positioning option is enabled(refer to SETUP), the cutting torch will move down until hit 
the lower limit switch. Then the cutting torch will move up until the hole positioning time delay is 
up.   

Summary of Contents for Stinger Series














































































Reviews:

No comments