manualshive.com logo in svg

arbo HD KR, User Manual

Share
Download
arbo HD KR User Manual Download Page 22

Installation

User Manual Chemical centrifugal pumps with mechanical seal  V080716

22

5.3

Electrical installation

/i

1. Electrically connect the product according to the tables above.

2. Remove the connection strips in case of a star-delta switch.

WARNING
-

If you do the electrical installation of the product, make sure 
that you are qualified. Obey the local regulations.

-

Make sure that you do not connect the electric motor of the 
product directly to the mains. 

-

Electrically earth the product in accordance with DIN VDE 0100.

-

Use a suitable main switch with adequate safety protection.

-

Read the sticker located on the inner side of the cover of the 
electrical connection box of the motor and compare the data 
with the available power supply.

-

Make sure that the security class of the motor complies with 
the local safety rules.

-

The available voltage and frequency must be the same as the 
voltage and frequency information on the motor identification 
plate.

Ty

p

e

Pole

Motor power

C

onn

ectio

n

Pole

Motor power

C

onn

ectio

n

KR-15-85 – KR-50-160

2

< 5.5kW 230/400V

4

< 2.2kW 230/400V

KR(V)/TK-80-160 – 150-250

2

≥

 5.5kW 400/690V 4/6/8

≥

 2.2kW 400/690V

CAUTION

For 400/690 V motors, a star-delta switch is strongly recommended.

U1

W2

U2

V1

W1

V2

L3

L1

L2

L2

L1

L3

V2

W1

V1

U2

W2

U1

U1

W2

U2

V1

W1

V2

L3

L1

L2

L2

L1

L3

V2

W1

V1

U2

W2

U1

L

N

Z1

V2

U2

V1

U1

Z2

1x 230V

3x 230V

400V

230/400V

230V

400/690V

C

M

V

M

V

690V

<2.2Kw

>2.2Kw

Summary of Contents for HD KR




































Reviews:

No comments

Brands by name

Popular brands

Load more brands