background image

Version: 20220420 

 

 4 

This symbol means that the product shall not be disposed of together with household or commercial waste. 

Directive  2012/19/EU  on  waste  electrical  and  electronic  equipment  (WEEE)  is  applicable  in  the  European  Union 
member states. To prevent potential harm to human health and the environment, the product must be disposed of in 
an approved and environmentally safe recycling process. For information about your nearest designated collection 
point, contact your local authority responsible for waste disposal. Businesses should contact the product supplier for 
information about how to dispose of this product correctly. 

This product complies with the requirements of Directive 2011/65/EU and 2015/863 on the restriction of the use of 
certain hazardous substances in electrical and electronic equipment (RoHS). 

This product uses a 3.0 V BR2032 lithium battery as the power supply for its internal real-time clock (RTC). Under 
normal conditions this battery will last for a minimum of five  years. Lithium coin cell  3.0 V batteries contain 1,2-
dimethoxyethane; ethylene glycol dimethyl ether (EGDME), CAS no. 110-71-4. 

Liability 

Every  care  has  been  taken  in  the  preparation  of  this  document.  Please  inform  Araani  NV  of  any  inaccuracies  or 
omissions.  Araani  NV  cannot  be  held  responsible  for  damage  caused  by  technical  or  typographical  errors  and 
reserves the right to make changes to the product and manuals without prior notice. Araani NV makes no warranty 
of any kind regarding the material contained within this document, including, but not limited to, the implied warranties 
of merchantability and fitness for a particular purpose. Araani NV shall not be liable nor responsible for incidental or 
consequential damages in connection with the furnishing, performance or use of this material. This product is only 
to be used for its intended purpose. 

Copyright Notice  

This  document  is  copyright  protected  and  is  the  property  of  Araani  NV  and  may  not  be  copied,  reproduced,  or 
distributed in any way without the prior written consent of Araani NV.  

©2015  Araani  NV.  Araani  is  a  registered  trademark  of  Araani  NV.  All  other  company  names  and  products  are 
trademarks or registered trademarks of their respective companies. We reserve the right to introduce modifications 
without notice.  

Trademark acknowledgements 

AXIS  COMMUNICATIONS  and  AXIS  are  registered  trademarks  or  trademark  applications  of  Axis  AB  in  various 
jurisdictions. All other company names and products are trademarks or registered trademarks of their respective 
companies. 

Ethernet, Torx, Microsoft, Milestone, Genetec and WWW are registered trademarks of the respective holders. 

 

This product complies with the applicable CE marking directives and harmonized standards: 

 

Electromagnetic Compatibility (EMC) Directive 2014/30/EU.  

 

Low Voltage Directive (LVD) 2014/35/EU. 

 

Restriction  of  Hazardous  Substances  (RoHS)  Directive  2011/65/EU  and  2015/863,  including  any 
amendments, updates or replacements.  

 

 

 

Summary of Contents for 8000004




























Reviews: