background image

4

P/N: 475-209

P/N: 475-209

 

 

OPTIONAL -  Insert Install Plate (P/N. 
475-209)

 

into Outer Frame with label 

facing upwards, and press down gently 
until it rests on stop ribs (A).
Adjust as required to ensure Outer 
Frame is level, square and top rim is 
flush with surrounding surface (B).

**WHILE MORTAR IS WET**

 To install Outer Frame:

1

2

3

4

**AFTER MORTAR HAS SET**

 To finish Outer Frame:

PREFERRED - Fill gap surrounding 
Outer Frame using a suitable
expansion joint gap filler (A).
ALTERNATE - Apply grout around 
Outer Frame perimeter using preferred 
mortar/grout compound*.
OPTIONAL - Remove Install Plate  
(P/N. 475-209) after compound is 
fully cured (B).

 

   

To lay mortar bed:

Using appropriate mortar mix, insert 
mortar into recess surrounding 
skimmer box opening (A). 

IMMEDIATELY REMOVE ANY MORTAR 

THAT FALLS INTO SKIMMER BOX 

IMMEDIATELY REMOVE ANY MORTAR 

THAT FALLS INTO SKIMMER BOX

To position Outer Frame:

Place Outer Frame on mortar bed. 
Mortar must fully support Outer 
Frame (A).
Ensure top rim of Outer Frame is flush 
with top face of surrounding stone/tile.
Remove any excess mortar and ensure 
skimmer box opening is fully 
accessible through Outer Frame (B).

OUTER FRAME INSTALLATION

 

-

 

STONE/TILE

* Using rigid grout or mortar may result in gaps/cracking appearing over time due to natural expansion & contraction.  

Summary of Contents for 475-201













Reviews: