AquatiControl Technology ELC-810 Series Operation And Maintenance Manual Download Page 10

 

ACT 2009 

- 10 -

 
 

ROUTINE MAINTENANCE

 

 

AquatiControl Technology’s Model ELC-810 controller is completely solid state 

and normally will not require any maintenance. 
 

S

ENSOR 

U

NIT 

C

LEANING

 

 

S

TANDARD 

W

ELL

 

The ½” PVC tube on the Standard Well Sensing Unit may need to be cleaned 
periodically.  To clean the tube, isolate the sensor unit by closing the valve that 
supplies the water to it.  Remove the cap from the top of the tube and fill with a 
diluted acid solution, 3 parts water to 1 part acid.  A brush may be used to clean 
the inside of the tube. 
 
The valve at the bottom of the sensing unit can be opened to drain out the acid 
solution. Place the solution into a container and dispose of it properly.  The tube 
can then be flushed with fresh water.  After flushing, open the valve from the 
pool.  The unit is now ready for operation. 

 

 

S

IGHT 

G

LASS

 

The Sight Glass Sensing Unit will not normally need to be cleaned. 
 

S

URGE 

T

ANK

 

The Surge Tank Sensing Unit will not normally need to be cleaned; however, if 
the cap on the bottom of the sensing application becomes clogged with debris, it 
can be unscrewed and rinsed until clean and then replaced.  
 

W

ET 

W

ELL

 

The Wet Well Sensing Unit will not normally need to be cleaned; however, if the 
cap on the bottom of the sensing application becomes clogged with debris, it can 
be unscrewed and rinsed until clean and then replaced.  
 

D

ECK 

W

ELL

 

The Deck Well Sensing Unit will not normally need to be cleaned; however, 
debris and stagnant water may enter the Deck Well which can be cleaned out 
being very careful not to get any water near the sensing unit or electrical conduit. 
 

S

ENSOR 

R

EPLACEMENT

 

 
 

The proximity switch used for the control system is good for thousands of on/off 

switching.  Typically the sensor should be replaced every three years for year round 
usage.  Seasonal pools may require replacing every five years or as needed. Replacement 
sensors are available from the distributor and factory for all but the surge tank sensing 
units which need to be replaced in whole.  

Summary of Contents for ELC-810 Series














Reviews: