background image

Tel: 1-800-661-0680

13

AQUASURE

USA

.com

Note:

 It is recommend to change your Stage 1 pre-filter at least every 4 - 6 month for 

areas with bad water quality. Check your filter label for more details.

Note:

 It is recommend to perform a backwash cycle for 15 minutes and fast rinse cycle 

for 5 minutes at least once a week.

SYSTEM MAINTENANCE

STEP 1. 

Shutting off the Supply Water

Caution!

 Before working on any system maintenance, get a clean cloth or microfiber towel to 

wipe off excess water that might spill during the filter replacement or system maintenance. 

1.  Turn the main water supply valve completely off by rotating it clockwise.

2.  Turn on the nearest faucet to release any excess water and pressure that is built up inside 

the pipe. 

STEP 2. 

Removing the Filter Housing

1.  Press the red pressure relief button on the top of the housing cap to relief any pressure 

built up inside the system.

 
2.  Using the housing wrench and turning it to the left to loosen 

3.  Discard the old filter and clean the inside of housing and cap with warm water.  

Caution!

 Do not use any chemical to wash the housing. 

STEP 3. 

Install the New Filter

1.  Unwrapped the filter and place it inside the housing and make sure the housing is 

centered on the stand pipe located inside the housing at the base.  

2.  Check the o-ring for cracks or damage. Replace o-ring if it is damaged. 

3.  Screw on the housing with filter inside to the corresponding head by turning it from left to 

right using the supplied housing wrench. 

Note:

 Make sure the o-ring is inside the housing and do not over tightening the housing. 

STEP 4. 

System Startup

1.  Turn on the main water supply valve fully by turning it counterclockwise
 
2.  Check for leaks

3.  Turn on the nearest faucet and let the water run for 10 minutes to release any trapped air 

bubble or carbon fine if a carbon filter is installed. 

IMPORTANT!

 A label can be found on the included filter cartridge. This label indicates the 

recommended duration of use before replacing the filter. This recommended time period 
should be considered starting from the point of first use.

Summary of Contents for FORTITUDE PRO Series





















Reviews: