background image

8

Connection node assembly
• Turn the water off at the cold water main.
• Open the kitchen faucet to discharge pressure 

into the water line.  

• Unscrew the nut from the flexible line cap, 

leading to the faucet on the cold water main. 

 ATTENTION! 

 Residual water will be left inside 

of the flexible JG tube after discharge of water.   
When disconnecting the flexible line, please use 
a 200 ml or similar size container to drain the 
water left behind in the tube.
• Screw the cap nut off the connection node and 

on the cold water main thread.

• Screw the cap nut off the flexible line, and then 

on the connection node thread.

• Set the shutoff valve on the connection node 

to the closed position and then make sure that 
the connection is completely leak-proof by sup-
plying water to the cold water main. 

• Connect JG tube (follow the instructions below 

to correctly connect the JG tubes). 

 ATTENTION! 

 Make sure that the sealing O-Ring 

is located correctly in its place and not damaged 
during installation.

Connection of JG tubes

Pull the locking clip (2) off the plastic plug (1). 
Then install the previously wetted end of the 
tube (3) into the fitting piece approx.15 mm up 
to the stop. Next, put the locking clip (2) back. 

Make sure that the tube (3) is tightened correctly: 
the tube should not be pulled out by force greater 
than 8-10 kgf.

Disconnection of JG tubes

Pull the locking clip (2) off the plastic plug (1), 
then pull the tube (3) out by applying pressure 
on the face of the connecting piece. To apply 
pressure, use the tube disconnection key (4) 
included in the water filter set.

6. Clean water faucet 
installation 

• Drill the hole in the sink (table top) 12 mm 

diameter;

• Put on the thread tail of the faucet (11) rubber 

gasket (2), decorative stand (3), rubber gasket 
(4) and insert the faucet into the hole in the sink;

Figure 5. 

Connection node installation scheme

Connection 

node

Sealing 

O-Ring

Cold water main

Locking clip 

Shutoff valve set 

in closed position

Figure 6. 

Connection of JG tubes

3

2

1

Figure 7. 

Disconnection of JG tubes

3

2

1

Summary of Contents for RO-101S

















Reviews: