AQUAPHOR RO-101S Owner'S Manual Download Page 7

7

When the clean water faucet is opened, water 
from the mains enters the technical chamber 
via the shutoff valve and forces treated water 
from the storage chamber through the faucet 

via the conditioning block. The automatic check 
valve then triggers and opens water supply to 
the RO-storage tank.

5. RO installation

 ATTENTION! 

 Only install your RO by a qualified 

plumber who is certified to perform the instal-
lation in accordance with state law.   
Locate the appropriate installation place for the 
faucet and RO. Take care to ensure that the de-
livery tubes are pulled freely, without over bend-
ing. RO must be installed on a flat, even solid 
surface as installation on an uneven surface may 
cause vibration or noise. Additionally, RO must 
be located away from heat sources, such as 
kitchen ovens, hot water supply pipes, dishwash-
ers or washing machines, or at least isolated 
from such heat sources. 

Water flow direction

Kitchen

faucet

Clean water 

faucet

RO housing

Drain saddle

Cold water 

supply 

Drain water

JG tube 1/4”

Connection node, 

shutoff valve 

in open position 

Incoming tap 

water JG 

tube 3/8” 

Treated water

JG tube 1/4”

Picture 4.

 RO installation scheme

How RO works

The water coming from the cold water mains 
enters RO and passes through the preliminary 
water treatment block. From there, water enters 
the Reverse Osmosis membrane block via the 
automatic check valve. The unit housing the 
membrane cartridge has two outlets: the treated 
water outlet and the drain water outlet. On its 
way to the drain, the water will also pass through 
a flow restrictor. The flow restrictor flushes the 
drain water that goes down the drain.
The treated water enters the storage tank that 
has a built-in membrane. This separates the tank 
into two chambers: storage and technical. The 
storage chamber contains the fully purified drink-
ing water, while the technical chamber contains 
water from the mains. As clear water collects, 
water from the mains is forced from the techni-
cal chamber into the drain, also preventing the 
accumulation of clear water. When the storage 
tank is full, the automatic check valve cuts off 
the water intake into RO.

Reverse 

Osmosis 

membrane

Incoming 

tap water

Pressure

Treated water

Summary of Contents for RO-101S

















Reviews: