background image

3

FEATURES & SPECIFICATIONS

MINIMONO BOAT SPECIFICATIONS:

Hull Length:

 16" [407mm]

Overall Length:

 18” [458mm]

Width:

 5.5" [140mm]

Height:

 3.25” [83mm]

Weight:

 10oz (28.5g) less battery

Run times:

 4 to 6 minutes

Speeds:

 Up to 25mph

BOAT FEATURES:

 

 

Tactic TTX300 2.4GHz transmitter with TR325 receiver

 

 

2200kV brushless outrunner motor

 

 

LiPo ready (3S) 20 Amp brushless motor controller with low 
battery warning system and battery cut off circuit

 

 

Tough, lightweight ABS construction with square hatch opening 
for easy taping

 

 

Great looking, pre-applied graphics

Other standard features include:

 

 

Surface drive propeller system

  Water cooled motor mount

  Music-wire drive shaft

  Break-away wedge rudder

  One piece aluminum fin-plates

  Transom mounted water pickup

  1/8" [3.2mm] prop shaft

  Two blade 30mm FRP propeller

  Transom drain plug

MOTOR SPECIFICATIONS:

KV Rating:

 2200kV

Operate Current:

 1.4A, 8V/DC (without loading)

Input:

 3-S LiPo Battery

Max Current:

 28A/15S

Shaft Diameter:

 3.175mm

Motor Resistance:

 50 m

Dimension:

 27.5 x 30mm

Weight:

 47g

MOTOR CONTROLLER:

Rated current:

 20amp

Battery Connectors:

 Male Hobbico Star Plug

Motor Connectors:

 3.5mm gold plated bullet connectors

Wire Gauge:

 14G

Stutter Bump Warning System:

 9.6V

Low Voltage Cutoff: 

9V

BEC Max Current:

 2A

PWM:

 8K

Dimensionx:

 45mm x 24mm x 9mm

SAFETY PRECAUTIONS

 

 Never, ever, attempt to swim after a stalled RC boat. DO NOT get 
in the water for any reason to retrieve your boat. Your Minimono 
has flotation added to the interior of the hull. It will not sink. To 
aid you in retrieving a stalled RC boat you can use a fishing reel 
with a tennis ball tied to the end of the line. Or better yet, get 
yourself a small Jon boat so you can row out and pick up your 
boat. Remember to use a personal flotation device any time you 
enter your retrieval craft.

 

 

AquaCraft products are to be used by ages 14 and over.

 

 

Do not touch the propeller anytime the motor is running. Pay equally 
close attention to items such as loose clothing, shirtsleeves, ties, 
scarves, long hair or anything that may become entangled in the 
spinning prop. If your fingers, hands, etc. come in contact with the 
spinning propeller, you may be severely injured.

 

 

The speed and mass of this boat can inflict property damage and 
severe personal injury if a collision occurs. Never run this boat 
in the presence of swimmers or where the possibility of collision 
with people or property exists.

 

 

Electric motors produce heat. Do not touch any part of your motor 
until it has cooled.

 

 

This boat is controlled by radio signals, which are susceptible 
to possible interference from other R/C transmitters, paging 
systems, or other electrical noise.

 

 

In the event that weeds become entangled in the propeller, stop the 
motor before attempting to remove them.

 

 

If your boat should happen to stall, water currents will slowly 
carry it to shore. Keep in mind that the boat could be carried to 
the opposite shore. When surveying areas to run your Minimono, 
keep variables in mind such as wind direction, size of the lake, etc. 
It is not advisable to run R/C boats on any free-flowing bodies of 
water such as creeks or rivers.

 

 

Always remove the battery pack from the boat before charging.

Summary of Contents for mini mono













Reviews: