background image

18

Two Available Water Manifolds Assemblies:

INSTALLATION 

(CONTINUED)

Inline-Cell Manifold Assembly (#75082)

 

SEE

 

INSTALLATION

 

DIAGRAM

NEXT

 

PAGE

The manifold is connected into the plumbing after all
other equipment. Water from the pool/spa is moved
though the manifold by the circulation pump. The man-
ifold's key components are the Tri-Sensor and SuperCell.

The Tri-Sensor provides data (from electronic sensors)
to the Control Unit for monitoring water flow, water
temperature, and salt concentration level. The Control
Unit uses this data to determine if conditions are safe
for the SuperCell to operate; the signal read from the
temperature sensor allows the automatic temperature
compensation feature to function.

The SC-36 SuperCell receives power from the Control
Unit and converts the salt contained in the water to
chlorine.

The manifold is connected into the plumbing after all
other equipment. Water from the pool/spa is moved
though the manifold by the circulation pump. The man-
ifold's four key components are the: Strainer Screen,
Tri-Sensor, SuperCell, and Bypass Flow Valve.

The Strainer Screen prevents debris in the water from
entering the Tri-Sensor or SuperCell, and requires
periodic inspection and cleaning.

The Tri-Sensor provides data (from electronic sensors)
to the Control Unit for monitoring water flow, water
temperature, and salt concentration level. The Control
Unit uses this data to determine if conditions are safe
for the SuperCell to operate; the signal read from the
temperature sensor allows the automatic temperature
compensation feature to function.

The SC-36 SuperCell receives power from the Control
Unit and converts the salt contained in the water to
chlorine.

The Bypass Valve allows the water flow rate to be slowed and optimized through the SuperCell, while
permitting the pump to continue to circulate water to-and-from the pool/spa at full flow rates. The slowed
water flow through the SuperCell results in a more efficient "Super-Chlorination” effect, resulting in improved
overall sanitization.

Automatic-Flow Bypass Manifold Assembly (#94105)

 

SEE

 

INSTALLATION

 

DIAGRAM

NEXT

 

PAGE

 

Tri-Sensor

SuperCell

Strainer Screen

Bypass Flow Valve

(

INSIDE

)

Summary of Contents for Pool Pilot Cubby Digital





















Reviews: