8
www.AquaProducts.com/Service
Internal Timed Operation
Internal Timed Operation enables owners of Power Supply models equipped with either Dial or Digital timers to customize
their cleaner’s automatic operating cycle to clean anywhere from 1 to 7 hours and then automatically shut OFF. Once shut
OFF the Internal Timed mode will not automatically turn the cleaner back ON.
1. Press the Main Power ON / OFF switch to the “ON” position.
2. Adjust the Timer Control to the desired cleaning time (1 to 7 hours) depending on suggested cleaning cycle for your
model, pool size and amount of debris in pool (i.e. more debris = longer cleaning time).
Dial Timers (Fig 8a):
Rotate Dial Timer clockwise to increase time (corresponding with the hour represented on the
face of the Dial Timer) and counterclockwise to decrease operating time.
Digital Timers (Fig 8b):
Press the Time Selector Arrows Button upwards to increase time or downwards to decrease
operating time. Each time you press up or down the digital face will display the number of hours of timed operation for.
(DIGITAL TIMERS) NOTE: When pressing the Main Power Switch to “ON” should the Green LED above the C-RUN Button blink
continuously then the Power Supply is currently set to the External Timed Operation mode and needs to be reset to the Internal
Timed Operation mode by doing the following. Press and hold the C-RUN Button for approximately 5 seconds until the Green LED
stops blinking and remains off. If it has stopped blinking and is off then the Internal Timed Operation mode is set.
3. Press the Safety Reset Button (Fig. 8a, 8b). Your cleaner is now set to its Internal Timer and will begin cleaning for
the amount of time set.
NOTE: Your Power Supply will remain in the Internal Timed Operation mode until you physically reset it to the External Timed
Operation mode and will not reset to the External Timed Operation mode even if the power to the Power Supply is turned off or
is set to the OFF position.
Digital Timer (Fig. 8b)
1. Turn the Main Power ON / OFF Switch to “ON.
2. Press the “C-Run” (Continuous Run) button until it is lit.
Your cleaner is now set to Continuous Run mode.
Dial Timer (Fig. 8a)
1. With your Power Supply OFF, rotate Dial Timer counter-
clockwise until you feel it “click”.
2. Press the Main Power ON / OFF Switch to “ON”. Your
cleaner is now set to Continuous Run mode.
Figure 8a
(Dial Timer)
Figure 8b
(Digital Timer)
Safety
Reset
button
Dial Timer
Display
Continuous
Run (CRUN)
button
IMPORTANT: In “Continuous Run” External Timed mode, the Safety Reset button feature becomes inactive and
can not protect models with this feature from accidental “out of water” start up. Therefore, it is imperative that
you always unplug the Floating Cable from its Power Supply when removing your cleaner from the pool!
WARNING: The mode for operating your cleaner should be set after the cleaner has been placed in the pool, the
Floating Cable has been plugged into the Power Supply and the Power Supply has been plugged into the Ground
Fault Circuit Interrupted (GFCI) / Residual Current Device (R.C.D.) protected 115V electrical outlet with the Power
Supply located at least 12 feet / 4 meters from the pool’s edge!
Time Selector
Arrow Buttons
Red “ON” LED
Digital Timer
Display
Green LED
Continuous Run Operation (C-RUN)
Continuous Run mode means that the cleaner will operate continuously until the ON / OFF Switch to is physically pressed
OFF or an external time source automatically turns OFF the power to the Power Supply. When manually pressing OFF,
to restart its operation you must physically press the Switch back to ON. For automatic ON / OFF operation in “C-Run”
mode, please refer to External Timed Operation instructions (Page 9).
No Adjustable Timer
If your Power Supply does not have an Adjustable Timer (Dial or
Digital), then it is considered to always be in Continuous Run mode.
1. Press the Main Power ON / OFF Switch to “ON”. Your cleaner
is now set to Continuous Run mode.
KNOWING / USING MODEL FEATURES
SETTING THE POWER SUPPLY TIMER (INTERNAL AND / OR EXTERNAL)
If your cleaner has an adjustable Dial or Digital timer, you can set it for
Continuous Run or Internal Timed Operation
. All
Power Supplies (Page 4; Fig. 4a-d) may be connected to an external, separately purchased timer, such as a house-type
timer or pool control system. In this
External Timed Operation
mode you cleaner can externally be set to automatically
turn ON / OFF / ON / OFF as needed.
