Applied Energy Solutions Maverick Installation And Operating Instructions Manual Download Page 15

 

CHARGER WARRANTY 

 

APPLIED ENERGY SOLUTIONS warrants that each new and unused battery charger manufactured and supplied with good workmanship is free from any known mechanical defect, 
provided that (A) the product is installed and operated in accordance with the accepted industrial standards and in accordance with the printed instructions furnished by APPLIED 
ENERGY SOLUTIONS, (B) the product is used under normal conditions for which designed, (C) the product is not used in a corrosive, abnormally dusty or high humidity moisture 
condensing environment, and (D) the product is not subjected to misuse or negligence, and the product receives proper care, protection and maintenance under supervision of 
competent personnel. 

Warranty Terms and Conditions 

 

APPLIED ENERGY SOLUTIONS  Maverick Industrial Battery Chargers are warranted for 2 Years

(1)

, which begins on the date of shipment from APPLIED ENERGY SOLUTIONS. 

 
NOTES: 

(1) 

Warranty covers parts and labor, 

               AC fuses and DC fuses are not warranted unless they are found to be defective prior to use. 
 
NON-TRANSFERABLE WARRANTY. This warranty is extended by APPLIED ENERGY SOLUTIONS only to the original user (purchaser) of new equipment from APPLIED 
ENERGY SOLUTIONS or one of its authorized agents. The product purchased under this agreement shall be used exclusively by the buyer. There shall be no third party beneficiary 
of this warranty. 
 
REPAIR LIMITATIONS.  APPLIED ENERGY SOLUTIONS has the right to site inspection and judgment of the claimed defects in any product covered by this warranty. APPLIED 
ENERGY SOLUTIONS' liability is limited to the repair of any defects found to exist by APPLIED ENERGY SOLUTIONS or, at APPLIED ENERGY SOLUTIONS' option, the 
replacement of the defective product.  
 
APPLIED ENERGY SOLUTIONS and its authorized agents shall not be liable for direct or indirect damages in excess of such repair or replacement. In no event shall the purchaser 
be entitled to recover for contingent expenses from, but not limited to, telephone calls, telegrams, travel expenses, lodging, duties and taxes, labor, rental or replacement equipment, 
loss of business or profit or other commercial losses. 
 
CONTINUED USE OF DEFECTIVE PRODUCTS. The continued use of an APPLIED ENERGY SOLUTIONS Industrial Battery Charger that is known to be defective VOIDS ALL 
WARRANTIES. 
 
REPAIR OF MODIFIED EQUIPMENT. Except as authorized in writing the warranty specified does not cover any equipment that has been repaired by any party other than 
APPLIED ENERGY SOLUTIONS or its authorized agents. Except as authorized in writing the warranty specified does not cover any equipment that has been modified, mechanically 
or electrically, by any party other than APPLIED ENERGY SOLUTIONS. 
 
WARRANTY EXPENSE LIMITATIONS. APPLIED ENERGY SOLUTIONS will limit the warranty expense of all chargers to be paid at a maximum of the original purchase price 
of the charger. 
 
The provisions of this warranty shall not apply to product in use outside of the continental USA. 
 
Except as stated above, all other warranties and conditions, either expressed or implied, including implied warranties of merchantability and fitness for a particular purpose, are 
excluded and buyer assumes all risk and liability resulting from the use of the goods. APPLIED ENERGY SOLUTIONS neither assumes or authorizes any persons to assume for 
APPLIED ENERGY SOLUTIONS any other liability in connection with the sale or use of the goods sold and there are no oral agreements or warranties collateral to or affecting this 
written warranty  When installing, servicing or operating these products, safe practices should be used by skilled and qualified technical persons.  

 

Summary of Contents for Maverick
















Reviews: