Applied Energy Solutions Maverick Installation And Operating Instructions Manual Download Page 11 | Manualshive

Page: 11 / 15

Applied Energy Solutions Maverick Installation And Operating Instructions Manual Download Page 11

10

SECTION 8 FAILURE MODE

9.2

BATTERY LOW VOLTS OVERRIDE

If  the  battery  voltage  measures  less  than  1.7  VPC,  the  charger  may  be  started  manually,  by
pressing  and  holding  the  STOP  button  for  more  than  10  seconds.  If  the  battery  does  not
increase  above  1.7  V/Cell  in  5  minutes  the  charger  will  shut  off  and  indicate  Low  Volts  Alarm
again,  otherwise the normal charge cycle will continue. This "grace period"  is intended to give
the battery time to recover from its over-discharged condition.

SECTION 9

CHARGER CABINET

SECTION 10

MONTHLY PREVENTIVE MAINTENANCE

11.1

MONTHLY PREVENTIVE MAINTENANCE

WARNING

HIGH VOLTAGES EXIST WITHIN THE CHARGER WHICH CAN CAUSE SEVERE

INJURY OR DEATH. TO ALLOW INTERNAL COMPONENTS TO DISCHARGE,

PLEASE WAIT AT LEAST 3 MINUTES AFTER DISCONNECTING THE AC POWER

BEFORE SERVICING. SERVICE SHOULD ONLY BE PERFORMED BY QUALIFIED

SERVICE PERSONNEL. IMPROPER SERVICING MAY DAMAGE THE CHARGER.



If a battery is being charged, terminate the charge by pressing the STOP button.



Disconnect the battery from the charger.



Remove AC power from the charger.

«
...
9
10
11
12
13
...
»

Summary of Contents for Maverick
















Reviews:

No comments