Apollo MultiSpot HQ5020, User Manual

Page: 6 / 28

User Manual: Multispot GII-HQ5020
V2.00 (08-2015)
22
■ Maintenance
This device does not need regular maintenance. It is protected by an internal fuse
located on the power supply PCB. If this fuse fails, this usually indicates an internal
fault requiring servicing by a qualified engineer. The fuse shall only be replaced by a
fuse of same specification, and the replacement has to be made by qualified personnel
obeying applicable safety rules.
■
Technical data MULTISPOT-GII-HQ5020
Panels/Output…………………………….1 panel, 4560 lmLEDs per panel: 20×4W 4-chip
Arrangement….. 20×1W red 10×1W green 10×1W blue 8×1W amber 12×1W white chip
Optics………………………………………………………………….Secondary, 25 degrees
DMX Control……………………………………………………………………...3-7 Channels
IP Rating………………………………………………………………20 (indoor)/65 (outdoor)
Mains Input……………………………………………………………. AC90-250V~ 50/60Hz
Power supply type………………………………………………………….……..switch mode
Power consumption.……………………………………………………….……………….95W
Fuse…………………………………………………………….internal (see service manual)
DMX connections…………………………………………………3 pin XLR (Male / Female)
Modulation Type…………..……….…………..………….Pulse Density Modulation (PDM)
Control protocol.......................................................................................DMX 512 (1990)
Dimensions (with straight bracket) WxHxD…………………….. 330.0 x327.0 x151.5mm
Weight…………………………………………………………………………...………….7.1kg
■ Standards
This product complies with the following standards:
EU electrical safety................................................EN60598-1:2008, EN60598-2-1:1989
EU general safety……………………………………………….…….………. EN60598-2-17
EU photobiological safety.........................................................................EN 62471:2008
EU EMC.......................................EN55015: 2006 + A1:2007, EN61547:1995 + A1:2000
EU Harmonics ...................................................................................EN61000-3-2:2006
EU Flicker …………………...…………………………………………….EN61000-3-3:2008
US safety ………….…………..………………………………………………………UL60065
US EMC………………………..…………………………………………………..FCC Part 15
This product meets both the EMC Directive 2004/108/EC and the Low Voltage Directive
2006/95/EC.
User Manual: Multispot GII-HQ5020
V2.00 (08-2015)
3
WARNING! Shock hazard. Equipment must be properly grounded.
WARNING! Hot surface. Risk of skin burn or skin irritation.
WARNING! Fire hazard.
WARNING! Laser radiation. Risk of surface damage.
WARNING! LED light emission. Risk of eye injury.
■ Security advice before use
General advice:
1. Read this manual completely before using the product.
2. Keep this manual in your records for future reference.
3. Follow all instruction printed in this manual.
4. Follow all printed security advice on the product itself.
5. Take care of enough distance between this product and sources of
hum and noise like electric motors and transformers.
6. Carry this product with greatest care. Punches, big forces and
heavy vibration may damage this product mechanically.
Protection from eye injury
1. Warning: Depending on the configuration of the device, this device
may reach or exceed the limits of EN62471, risk group 2, and may
hence reach to risk group 3.
2. To avoid eye injury, do not look into the beam from a distance of
less than 8.5 m (27 ft. 11 ins) from the front surface of the fixture
without protective eyewear such as shade-5 welding goggles. At
larger distances, light output is harmless to the naked eye provided
that the eye’s natural aversion response is not affected.
3. Do not view the beam directly with optical instruments such as
magnifiers, telescopes, binoculars or similar optical instruments
that may concentrate the light output.
4. Ensure that during setup and DMX programming, no persons are
inside a 8.50m (27 ft. 11 ins) vicinity of the device’s front surface, to
avoid that they may accidently be exposed to the light beam.