Apelson CMA6SS, User Manual

Page: 10 / 24

10
Never extract the water tank while the machine is
delivering coffee If it is removed, it will not be possible to
make the coffee and the appliance will display “fill water”.
Put the water tank in original position, the interrupt
program will go on to finish.
CHANGING THE QUANTITY OF COFFEE IN
THE CUP
The appliance is set by default to automatically make the
following types of coffee:
1 cup of coffee when the button is pressed.
2 cups of coffee when the button is pressed.
To change these quantities, proceed as follows:
During make coffee the LCD display value “**CC”, rotate
the stand-by knob in any direction and LCD display
constant value, reach you require value, if machine reach
the value and automatic to stop.
ADJUSTING THE COFFEE MILL
The coffee mill is preset in the factory to make coffee
correctly and should not require adjusting initially.
However, if after making the first few coffees you find that
delivery is either too fast or too slow (a drop at a time),
this can be corrected by adjusting the grinding adjustment
knob.
IMPORTANT!
The grinding adjustment knob must only be rotate when
the coffee mill is in operation. For slower delivery and
creamier coffee, rotate one click anticlockwise (finer, pre-
ground coffee). For faster delivery (not a drop at a time),
turn one click clockwise (coarser pre-ground coffee).
Coffee has been used to factory test the appliance and it
is therefore completely normal for there to be traces of
coffee in the mill.
MAKING ESPRESSO COFFEE WITH
PRE-GROUND COFFEE
If appliance displays the message ‘READY’.
Extract the machine by pulling it outward using the
handles. Open the central lid, place one measure of pre-
ground coffee in the funnel, use a spoon To pure a cup
of coffee powder, then close the tap, and then you can
pressing the 1 cup or 2 cup button once only.
The next process is same as make coffee use beans. After
using the machine with pre-ground coffee, this machine
will go back to making coffee using beans.
Never introduce pre-ground coffee when the machine is
off.
Never add more than 1 level measure, otherwise the
appliance will not make the coffee and the pre-ground
coffee will be dispersed inside the appliance, dirtying it or
the coffee will be delivered a drop at a time.
Use the measure provided to add the right amount of
coffee---use spoon.
Introduce only pre-ground coffee for espresso coffee
machines into the funnel. Never fill with coffee beans,
freeze dried coffee or other substance that could damage
the appliance.
lf more than one measure of pre-ground coffee is used
and the funnel clogs, push the coffee down with a
knife clean the infuser and machine as described in the
“Cleaning the infuser section”.
DELIVERING HOT WATER
The appliance is set by default to automatically deliver
200ml of hot water.
Always make sure the appliance is in “ready” state.
Open the steam/hot water valve then water flow from
nozzle and LCD display “hot water”. LCD display the
quantity of the hot water, you can rotate stand by knob to
set the quantity.
If hot water output reach the set quantity, the pump will
stop and LCD display “close tap”. After close the tap LCD
again display “ready” (You should not deliver hot water for
more than 200cc at a time).
To interrupt the flow, close the tap is ok.
Once the set quantity of hot water has been reached,
delivery stops automatically.
MAKING CAPPUCCINO (USING THE STEAM
FUNCTION)
Insert a special accessory in the Steam nozzle.
Take a container, fill it with about 100 ml milk or use the
milk box.
You are recommended to use partially skimmed at
refrigerator temperature. When LCD display “ready”, press
“steam/hot water” button then LCD display ”heating” until
LCD display “steam ready” and “open tap”.
Turn on the steam/hot water valve and steam may spray
out from the nozzle. To stop steam deliver close the tap is
ok.
Immerse the cappuccino maker in the milk container. take
DAILY OPERATION OF YOUR COFFE MACHINE