background image

The Force Dual Phase™ Operation Manual 

 

10 

Revision Date: 4/22/2019 

 

2.3.8. 

Alarm Screen 

2.3.8.1.  The Alarm Screen is used for troubleshooting and where navigation to the Email 

Messaging Screen is located. When the system faults for any reason, it is 

recorded on the Alarm Screen. Often the fault you see on the home screen may 

have been caused by a series of faults. By looking at the alarm screen, you can 

see all the previous faults in the order  they occurred. 

 

 

Figure 10. Alarm Screen 

 

2.4. 

Pre-Cleaning 

2.4.1. 

The Force™ Dual Phase 5000psi systems are constructed from 304 and 316 stainless 

steel and can be cleaned with any cleaner that is compatible with both stainless steel 

and your extracted product. Simple Green cleaner, ethanol/alcohol work well for most 

applications. 

2.4.2. 

The system should be cleaned to the appropriate level (determined by your application 

and corresponding regulations) prior to processing each batch of botanical material. 

2.4.2.1.  Apeks takes great care to clean all systems prior to shipping. However, it is the 

user’s responsibility to ensure that the system meets the required level of 

cleanliness. 

 

 

Summary of Contents for THE FORCE 20Lx20LDP












































Reviews: