background image

4

Part II. System Maintenance

RO-CTOP-C & RO-CTOP-PHC FILTER CHANGE SCHEDULE

FILTER CHANGE INSTRUCTIONS

Stage-1 & Stage-2           

Replace every

 6-8 months.

                                       
                                       

(Private well water source: may need to replace pre-filters sooner than

                                          8 months due to heavy sediments and other particles.)

Stage-3 Membrane:        City Water: 

Replace every

 2-3 years 

depending on input water

                                          quality, water usage, and pre-filters change maintenance.

                                       Private Well Water: 

Replace every

 2 years 

depending on well water

                                          quality, and pre-filters change maintenance.

Stage-4 Post-Filter:          For RO-CTOP-C System: 

Replace every

 2-3 years. 

It’s best to replace

                                          this filter when replacing the stage-4 membrane.

                                       For RO-CTOP-PHC System: 

Replace every

 6-12 months.

Important! 

It is important to change the 2 pre-filters timely, at least every 6-8 months. The pre-filters pro-

tect the stage-3 membrane. If they are not changed timely and become over-depleted, the membrane will 
be damaged and the RO system will be contaminated.

It’s best to use APEC replacement filters. Using “non-APEC” and lesser quality filters may clog up the RO 
system and damage the membrane.

2. Filter Ports:  

All filters have Quick-Connect ports. Remove and connect tubing to filter ports as shown 

in the “Quick-Connect Guide” diagram. (See 

Figure D1-D3 

in the next page).

 

1. Removing Case:  

The system comes with a premium case. The top half of the case will need to be re-

moved to replace the filters inside. To remove the top cover, you will need to remove the 

2 bottom screws 

ONLY

 on each end of the case. Please 

DO NOT

 remove the top 2 screws (See 

Figure C 

in the next page).

3. Removing Filters:  

Please change 

one filter at a time

 to avoid mixing up the filters. New filters come 

with 2” protective plugs on each end. You can take them out by pressing on the collet ring with one finger 
and using a pair of pliers or hand to pull out the protective tubing (See 

Figure D1 

in the next page).

The system requires very little maintenance. Just change the filter cartridges regularly as suggested below.
Keep the system indoors away from extreme hot or cold temperatures, and run the system within its reason-
able output capacity (i.e. allow the system to rest at least a few hours a day).

Pre-Filters:

Summary of Contents for RO-CTOP-C

















Reviews: