background image

3

Part I. HOOK UP THE RO COUNTERTOP SYSTEM TO YOUR HOME FAUCET

System hook up:

 

 Remove your faucet’s aerator (if there is one). Hook up the RO system’s faucet adapter to 

your faucet (see

 Figure A

). If the connection does not match, try using the other Valve Adapters provided.

Point A.

 This is the Pure Water 

Outlet Line. Please remove the Red 
Cap from the end of the tubing. 

Point B.

 Please hook up faucet 

adapter to your kitchen faucet.

Figure A

Figure B

1.    

Feed water:

  Turn the faucet on to 

FULL

 (cold water only) to supply maximum water pressure to the 

RO system. Tap water will flow out the bottom of the diverter head. Simply turn the black knob on the 
diverter head Clockwise to direct the water into the RO system (See Point C, Figure B). Turn back knob 
Counter Clockwise to shut off water to the RO unit (See Point D, Figure B).

If input water is very cold, you can adjust the faucet to supply 

Luke

 warm water (

No Hot

 Water 

Please!). Strong input water pressure and warm water temperature will help increase output flow rate.

2.    

Pure Water: 

 Remove the red cap from end of the pure water output tubing (

See Point A, Figure A

)   

       place the tubing in your water container to catch the pure water.  

3. 

Drain water:

  Drain (waste) water will drain through the drain outlet on the diverter head (all reverse 

osmosis systems need to generate drain water to make pure water).

4. 

Flushing system:

  Let the RO run for 10-15 minutes to flush out the new Membrane – discard the 

output water during the flush. When done flushing, the fresh pure water is now ready for your enjoyment!

Summary of Contents for RO-CTOP-C

















Reviews: