APE 100 WICK Operating And Maintenance Manual Download Page 21 | Manualshive

Page: 21 / 65

background image

OPERATING

INSTRUCTIONS

III-3

MODEL 100

BOTTOM DRIVE

WICK INSERTER

III. OPERATING

INSTRUCTIONS

D. CHANGING FREQUENCY

1. In order to provide maximum fl exibility in achieving optimum mandrel penetration and

extraction rates, the frequency of the vibration gear box is adjustable. This adjustment
is made by the amount of hydraulic oil provided to the motor through the control valve
handle.

2. The frequency can be varied from 800 to 1650 vibrations per minute by changing engine

speed or the position of the control valve handle. Engine speed is changed with the
ENGINE THROTTLE and the position of the control valve handle.

G. SHUT DOWN

1. Stop the vibration gear box and mandrel drive motors.

2. Allow the diesel engine to run for fi ve minutes at 1500 RPM.

3. Reduce speed to low idle for about thirty seconds.

4. Stop the engine by turning the ENGINE START switch to OFF.

«
...
19
20
21
22
23
...
»

Summary of Contents for 100 WICK


































































Reviews:

No comments

Related manuals for 100 WICK

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

Brand: IBS Scherer Pages: 64

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: S.R.Smith Pages: 8

Brand: S.R.Smith Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands