AOR AR6000 Operating Manual Download

Page: 7 / 95

Main features:

Wide frequency coverage: 9 kHz to 6 GHz, with no interruptions

(Cellular blocked for the US consumer version)

45.05 MHz IF DSP (Digital Signal Processing)

HF direct sampling

No AGC in the analog processing circuit

Computer simulated high grade RF frontend

PC controllable

DDS (Direct Digital Synthesizer) local oscillator

Accurate reference frequency (0.01 ppm with an optional GPS unit)

Analog TV reception in both NTSC and PAL formats

IF analog signal output (45.05 MHz, +/- 7.5 MHz for a total of 15 MHz bandwidth)

Multi-mode unit capable of receiving AM (Synchronous), ISB, USB, LSB, CW, AIQ (AF-IQ),

WFM including FM stereo (optional headphone or stereo speakers required), NFM and

P25 (APCO25) digital (optional)

Composite video output on the rear panel of the unit

SD card interface

Selectable IF bandwidths: 200 Hz, 500 Hz, 1kHz, 3 kHz, 6 kHz, 15 kHz, 30 kHz, 100 kHz, 200 kHz,

along with the ability to shift the IF

CTCSS and DCS selectable squelch functions

DTMF tone decode

Built-in voice-inversion descrambling (Not available for the US consumer version)

CW pitch control, AGC, AFC

Auto-notch, noise reduction (NR), noise blanker (NB)

Fast Fourier Transform (FFT) analyzer for fast spectrum display processing

12 kHz (analog) I/Q output for DRM® PC receiver

USB 2.0 interface

Two antenna ports (Type N)

Up to 4 antenna ports (Optional antenna switch required)

5 VFO’s, 2,000 alphanumeric memories

Simultaneous monitoring of up to three channels

Digital Voice Recording (with a SD memory card)

I/Q output with 0.9 MHz bandwidth (with an optional I/Q unit)

LAN (Local Area Network) control (with an optional LAN interface)

P25 (APCO25) decode (conventional mode) (with an optional P25 unit)

Antenna input level readout (in dBm, dB

selectable)

Summary of Contents for AR6000
































































































Search results

Summary of Contents for AR6000

Reviews:

Related manuals for AR6000

Brands by name

Popular brands

AOR AR6000, Operating Manual

Search results

Summary of Contents for AR6000

Reviews:

Related manuals for AR6000

Brands by name

Popular brands