-L*A1AW 11/12-
32
72
36.7
70
10
■
LB-A1AW
(Extension unit)
14.25
■
Individual specifications
[Outside Dimensions]
Unit: mm
32
72
36.7
70
10
■
LA-A1AW
(Base unit)
Φ
4.1
Φ
1.1
Four cores, AWG24
Cable length: 200mm
■
Transmission line
Transmission line
(200)
* The length of LB-S24 is also the same.
■
Transmission specifications
[Specifications]
0 - 55°C, 10 - 90%RH (No condensation)
Ambient temperature/humidity for use
-25 - 75°C, 10 - 90%RH (No condensation)
Ambient temperature/humidity for storage
No corrosive gas
■
General Specifications
Atmosphere for use
0 to 2000m
Altitude of use *
1
1200Vp-p
Resistance to noise
2 or less
Pollution level *
2
*1 Do not use or store the AnyWireASLINK device in an environment pressurized equal to
or higher than the atmospheric pressure at the altitude of 0m. Doing so could cause a
malfunction.
*2 Index that indicates the occurrence of conductive material in the environment where the
device is used.
Contamination level 2 indicates that only non-conductive contamination occurs.
However, incidental condensation could create temporary conductivity in this
environment.
DC power supply superimposed total frame/cyclic method
Transmission method
Frame/bit synchronization method
Synchronization method
Dedicated protocol
Transmission procedure
Number of connection points
Number of units connected
RAS feature
Voltage 24V DC +15% to -10% (21.6 to 27.6V DC)
Power supply
voltage for use
Ripple of 0.5Vp-p max.
512 max. (IN: 256, OUT: 256)
Up to 128 units
Bus type (Multi-drop method, T-branch method, Tree branch method)
Connection mode
Transmission line disconnection, transmission line
short-circuit, transmission power supply reduction
detection ID redundancy, ID not set
LA-A1AW: Input 16 points (Base unit)
LB-A1AW: Input 16 points (Extension unit)
When connecting only LA-A1AW and LB-A1AW
(LA-A1AW: n d(LB-A1AW: m devices)
≦
16 devices
Number of
occupied points
Number of
connection
devices
20 mA (DP-DN) (Base unit)
20 mA (DP-DN) (Extension unit)
Consumption
current
1CH (Base unit)
1CH (Extension unit)
Number of
analog input CH
0 - 10V, 0 - 5V, 1 - 5V (Input impedance 100kΩ or more)
0 - 20 mA, 4 - 20 mA (Input impedance within 250Ω±5%)
±0.1% (16digit)
Measurement voltage range
Measurement current range
Accuracy
（
25
℃）
±0.2% (32digit)
（
0
～
55
℃）
Input range
Digital input value
0-10V
0-5V
0-16000
0-16000
0-16000
0-16000
0-16000
Resolution
625uV
312.5uV
250uV
1250nA
1000nA
Input
characteristics/
Resolution
1-5V
0-20mA
4-20mA
12V, 30 mA
Absolute MAX input
5ms
Response time *
3
External supply
current
22 g (Base unit)
17 g (Extension)
Mass
Input abnormality
Input value over
Analog port open, disconnection: Digital value -200, ALM Display OFF
Over the lower limit: Digital value -200, ALM display ON, Lo _ _ display
Over the upper limit: Digital value 16200, ALM display ON, hi
_ _
display
*3 Time from detection of ON or OFF to sending of transmission signal.
This time plus the transmission 2 cycle time are transmission delay time.
When connecting the power supply unit (LB-S24) to
each analog input unit Available supply: Between
24V-0V, MAX 100 mA/CH
