background image

Limited Warranty

Equipment manufactured by Antunes has been constructed of the finest materials available and manufactured to 

high quality standards.  These units are warranted to be free from electrical and mechanical defects for a period of 

one (1) year from date of purchase under normal use and service, and when installed in accordance with manufac

-

turer’s recommendations.  To insure continued operation of the units, follow the maintenance procedures outlined 

in the Owner’s Manual.  During the first 12 months, electromechanical parts, non-overtime labor, and travel ex

-

penses up to 2 hours (100 miles/160 km), round trip from the nearest Authorized Service Center are covered.

1. 

This warranty does not cover cost of installation, defects caused by improper storage or handling prior to plac

-

ing of the Equipment.  This warranty does not cover overtime charges or work done by unauthorized service 

agencies or personnel.  This warranty does not cover normal maintenance, calibration, or regular adjust

-

ments as specified in operating and maintenance instructions of this manual, and/or labor involved in moving 

adjacent objects to gain access to the equipment.  This warranty does not cover consumable/wear items. This 

warranty does not cover damage to the Load Cell or Load Cell Assembly due to abuse, misuse, dropping of 

unit/shock loads or exceeding maximum weight capacity (4 lbs).  This warranty does not cover water con

-

tamination problems such as foreign material in water lines or inside solenoid valves.  It does not cover water 

pressure problems or failures resulting from improper/incorrect voltage supply.   This warranty does not cover 

Travel Time & Mileage in excess of 2 hours (100 miles/160 km) round trip from the nearest authorized service 

agency. 

2. 

Antunes reserves the right to make changes in design or add any improvements on any product.  The right 

is always reserved to modify equipment because of factors beyond our control and government regulations.  

Changes to update equipment do not constitute a warranty charge.

3. 

If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier.  Careful inspec

-

tion should be made of the shipment as soon as it arrives and visible damage should be noted upon the car

-

rier’s receipt.  Damage should be reported to the carrier.  This damage is not covered under this warranty.

4. 

Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes.  All such 

freight and taxes are the responsibility of the purchaser.  

5. 

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR 

IMPLIED, INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICU

-

LAR PURPOSE, EACH OF WHICH IS HEREBY EXPRESSLY DISCLAIMED.  THE REMEDIES DESCRIBED 

ABOVE ARE EXCLUSIVE AND IN NO EVENT SHALL ANTUNES BE LIABLE FOR SPECIAL CONSEQUEN

-

TIAL OR INCIDENTAL DAMAGES FOR THE BREACH OR DELAY IN PERFORMANCE OF THIS WAR

-

RANTY.

The warranty does not extend to:

 

y

Damages caused in shipment

 

y

Installation of electrical service

 

y

Installation, calibration, or adjustment

 

y

Normal maintenance outlined in this manual

 

y

Consumable parts such as egg rings, gaskets, rubber feet, labels, O-rings, light bulbs, etc.

 

y

Malfunction resulting from improper service or maintenance

 

y

Damage caused by improper installation, improper use, abuse, or careless handling

 

y

Damage from moisture coming in contact with electrical components

 

y

Damage from tampering with, removal of, or changing preset controls or safety devices

 

y

Damage caused by parts or components not  provided by Antunes

®

Corporate Headquarters

Carol Stream, IL, USA
Phone:

 +1.630.784.1000

Toll Free:

 +1.800.253.2991

Fax: 

+ 1.(630).784-1650

China Facility 

Suzhou, China 
Phone: 

+84.512.6841.3637

Fax: 

+86.512.6841.3907

India Facility

Chennai, India
Phone:

 +91.44.25532212

Fax:  

+91.44.25532415

Summary of Contents for 9210914

























Reviews: