®
P/N 1011436 Rev. H 02/21
10
Maintenance
Daily Cleaning
WARNING
Turn the power off, unplug the power
cord, and allow the unit to cool to room
temperature before performing any
service or maintenance.
1.
Turn the power OFF, unplug the
power cord, and clean the release
sheet and belts wraps while they are
warm.
Non-Butter Wheel Unit Butter Wheel Unit
2.
Put on heat-resistant gloves. Remove
the Bun Feeder and Bun Chute.
Non-Butter Wheel Unit Butter Wheel Unit
3.
Take the Bun Feeder and Bun Chute
to the sink and wash, rinse, and
sanitize.
4.
Remove the release sheet and place
it on a clean, flat dry surface.
5.
Inspect the release sheet and belt
wraps. Replace if they are torn,
damaged, or have excessive buildup.
6.
Spray the silver side of the release
sheet with Sink Detergent Solution
and wipe with a clean, sanitizer-
soaked towel. Rinse the silver side of
the Release Sheet with a separate,
clean sanitizer-soaked towel.
7.
Flip the release sheet over and spray
the black side with Sink Detergent
Solution and wipe with a clean,
sanitizer-soaked towel. Rinse the
black side of the release sheet with
a separate, clean sanitizer-soaked
towel. Discard the soiled towel into the
soiled towel bucket after use. Allow to
air dry.
8.
Open the front conveyor cover and
firmly wipe the belt wrap from left to
right and top to bottom with a clean,
sanitizer-soaked towel sprayed with
an approved Degreaser solution.
Rinse the belt wrap from left to right
and top to bottom with a separate,
clean sanitizer-soaked towel.
9.
Close the front conveyor cover, open
the rear conveyor cover and clean the
belt wrap following step 8. Discard
the soiled towels into the soiled towel
bucket after use.
10.
Close the rear conveyor cover. Plug
in the power cord, turn the unit, allow
belt to make a 1/2 revolution, then turn
the unit OFF and unplug the unit.
11.
Open the rear conveyor cover again
and clean the newly exposed section
of the belt wrap from left to right and
top to bottom with a clean, sanitizer-
soaked towel sprayed with degreaser
solution. Rinse the belt wrap from
left to right and top to bottom with
a separate, clean, sanitizer-soaked
towel.
12.
Close the rear conveyor cover, open
the front conveyor cover and clean the
belt wrap following step 11. Discard
the soiled towels into the soiled towel
bucket after use. Close the front
conveyor cover.
13.
Wipe down the exterior of the toaster
with a clean, sanitizer-soaked towel
sprayed with a Degreaser solution.
Rinse the exterior toaster with a
separate, clean sanitizer-soaked
towel. Discard the towel into the soiled
towel bucket after use.
14.
The release sheet has folded gutters
to prevent debris migration onto the
platen. Prior to installing the sheet,
fold the gutters 90 degree if needed.
Install the release sheet by draping it
over both sides of the platen with the
black side facing out.
NOTE:
The release sheet is not
reversible, the black side should
always be facing out.
15.
Reinstall the Bun Chute through the
front of the toaster. Hang the back of
the Bun Chute on the rear Conveyor
Cover hinge. See Figure 2 on page 5.
Reinstall the Bun Feeder.
Rear
Conveyor
Cover Hinge
Insert Bun Chute
through front of unit.
Bun Chute is properly
installed when it hangs
from the rear Conveyor
Cover hinge.
16.
Plug the toaster in and turn the power
switch to ON.
