ANTAIRA LNP-0500G-24 Series User Manual Download Page 6 | Manualshive

Page: 6 / 20

background image

2

Antaira Technologies - Industrial Ethernet Switches

LNP-0500G-24 Series User Manual V1.0

1.2 Package Contents



1 - LNP-0500G-24 (-T): 5-port industrial Gigabit PoE+ unmanaged Ethernet switch

with 4*10/100/1000Tx (30W/port) and 1*10/100/1000Tx



1 - Product CD



2 - W all mounting brackets and screws



1 - DC cable

–18 AWG & DC jack 5.5x2.1mm

1.3 Safety Precaution

Attention:

If the DC voltage is supplied by an external circuit, please use a protection

device on the power supply input. The industrial Ethernet switch

’s

hardware specs, ports, cabling information, and wiring installation will be

described within this user manual.

«
...
4
5
6
7
8
...
»

Summary of Contents for LNP-0500G-24 Series





















Reviews:

No comments

Related manuals for LNP-0500G-24 Series

Brand: CALIENT Pages: 46

Brand: CALIENT Pages: 42

WJSX150 - SWITCHER - ADDENDUM

Brand: Panasonic Pages: 48

Brand: Campbell Pages: 14

Brand: OEZ Pages: 5

Brand: DITEC Pages: 8

Draco major K474-U8/C8

Brand: Ihse Pages: 167

Brand: steute Pages: 10

Brand: West Mountain Radio Pages: 10

Brand: Fairchild Pages: 19

TurboIron 24X series

Brand: Brocade Communications Systems Pages: 82

Brand: Wavetronix Pages: 3

Brand: Manhattan Pages: 2

SmartSwitch SBU128

Brand: Cabletron Systems Pages: 76

Brand: Radware Pages: 4

DOMINION KX II DKX2-0E-E

Brand: Raritan Pages: 257

Brand: Qlogic Pages: 412

Clear Switch CF-POE8

Brand: ANTIFERENCE Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands