ANTAIRA LMP-0501 Series User Manual Download Page 19

Page: 19 / 80

Antaira Industrial Ethernet Switches

LMP-0501 Series User Manual V1.0

4. Hardware Installation

4.1 Installation Steps

This section will explain how to install Antaira

’s LMP-0501 series: 5-port industrial PoE+ managed

Ethernet switch with 4*10/100Tx (30W/Port) RJ45 ports and 1*100Fx (SC/ST) fiber port.

Installation Steps

1. Unpack the industrial Ethernet switch from the original packing box.

2. Check if the DIN-Rail bracket is screwed on the industrial Ethernet switch.



If the DIN-Rail is not screwed on the industrial Ethernet switch, please refer to the

DIN-Rail Mounting

section for DIN-Rail installation.



If you want to wall mount the industrial Ethernet switch, please refer to the

Wall

Mounting

section for wall mounting installation.

3. To hang the industrial Ethernet switch on a DIN-Rail or wall, please refer to the

Mounting

Installation

section.

4. Power on the industrial Ethernet switch and then the power LED light will turn on.



If you need help on how to wire power, please refer to the

Wiring the Power Inputs

section.



Please refer to the

LED Indicators

section for LED light indication.

5. Prepare the twisted-pair, straight-through category 5 cable for Ethernet connection.

6. Insert one side of the RJ-45 cab

le into switch’s Ethernet port and on the other side into the

networking device’s Ethernet port, e.g. switch PC or server. The Ethernet port’s (RJ-45) LED

on the industrial Ethernet switch will turn on when the cable is connected to the networking

device.



Please refer to the

LED Indicators

section for LED light indication.

7. When all connections are set and the LED lights all show normal, the installation is complete.

Summary of Contents for LMP-0501 Series

















































































Search results

Summary of Contents for LMP-0501 Series

Reviews:

Related manuals for LMP-0501 Series

Brands by name

Popular brands

ANTAIRA LMP-0501 Series, User Manual

Search results

Summary of Contents for LMP-0501 Series

Reviews:

Related manuals for LMP-0501 Series

Brands by name

Popular brands