Ansul AUTOPULSE IQ-636X Operation Manual Download Page 37

Page: 37 / 84

Output Circuit Trouble Mode of Operation

3. Operation of the Control Panel

IQ-636X Operations Manual P/N 52181:A 04/28/2005

How to Respond to a NAC, Panel Circuit or Control/Relay Trouble

If the control panel indicates an active NAC, Panel Circuit or Control/Relay Trouble, take the following action:

1. Press the

ACKNOWLEDGE

SCROLL

DISPLAY

key to silence the panel sounder and switch the

SYSTEM

TROUBLE

LED from flashing to steady—regardless of the number of troubles, alarms, and

supervisory signals.

2. The control panel sends an Acknowledge message to the History buffer and installed printers,

terminal mode LCD-80s, and CRT-2s. Check the trouble message for the location and type of
trouble.

3. Correct the condition causing the trouble.

4. When the trouble condition is corrected, the panel will return to normal operation (indicated by the

“System Normal” message).

5. The control panel sends a “System Normal” message to the LCD display, History buffer and

installed printers, terminal mode LCD-80s, and CRT-2s.

Summary of Contents for AUTOPULSE IQ-636X





















































































Search results

Summary of Contents for AUTOPULSE IQ-636X

Reviews:

Related manuals for AUTOPULSE IQ-636X

Brands by name

Popular brands

Ansul AUTOPULSE IQ-636X, Operation Manual

Search results

Summary of Contents for AUTOPULSE IQ-636X

Reviews:

Related manuals for AUTOPULSE IQ-636X

Brands by name

Popular brands