Ansul AUTOPULSE IQ-636X Operation Manual Download Page 6

Page: 6 / 84

IQ-636X Operations Manual P/N 52181:A 04/28/2005

How the Control Panel Indicates an Active Non-Fire Point ................................... 33

Active Trouble Monitor Mode of Operation

........................................................... 34

How the Control Panel Indicates an Active Trouble Monitor ................................ 34
How to Respond to an Active Trouble Monitor...................................................... 34

Output Circuit Trouble Mode of Operation

........................................................... 35

Operation of Special System Timers

........................................................................ 38

What are System Timers? ....................................................................................... 38
How to View System Timer Selections .................................................................. 38
How System Timers Work...................................................................................... 38

Auto Silence Timer ............................................................................................. 38
Alarm Verification Timer ................................................................................... 38
Silence Inhibit Timer .......................................................................................... 39

Waterflow Circuit Operation

................................................................................... 39

Style 6 and Style 7 Operation

................................................................................... 39

4. Read Status Operation

Introduction

............................................................................................................... 41

What is Read Status?

................................................................................................ 41

Quick Reference Key Sequences ............................................................................ 41

Entering Read Status

................................................................................................ 41

Viewing and Printing a Read Status

........................................................................ 42

How to View Read Status of Devices, Zones, and System Settings....................... 43

How to View Read Status for Event and Alarm History ........................................ 51

Overview............................................................................................................. 51
How to View Read Status for Event History...................................................... 51
How to View Read Status for Alarm History ..................................................... 52

How to Print Points, Event and Alarm History....................................................... 53

Overview............................................................................................................. 53
How to Print Points............................................................................................. 53
How to Print Event History ................................................................................ 53
How to Print Alarm History................................................................................ 53

How to View and Print Hidden Event and Alarm History...................................... 54

Appendix A: Special Zone Operation

Overview

..................................................................................................................... 55

Releasing Zones (R0-R9)

........................................................................................... 56

Purpose of Releasing Zones ................................................................................. 56
How to View Releasing Zone Selections................................................................ 56
How Releasing Zones Operate................................................................................ 57

Summary of Contents for AUTOPULSE IQ-636X





















































































Search results

Summary of Contents for AUTOPULSE IQ-636X

Reviews:

Related manuals for AUTOPULSE IQ-636X

Brands by name

Popular brands

Ansul AUTOPULSE IQ-636X, Operation Manual

Search results

Summary of Contents for AUTOPULSE IQ-636X

Reviews:

Related manuals for AUTOPULSE IQ-636X

Brands by name

Popular brands