manualshive.com logo in svg

Anatomic SITT Zitzi Seabass Pro, User Manual, Page: 32 / 56

Share
Download
Anatomic SITT Zitzi Seabass Pro User Manual Download Page 32

32

User manual  Zitzi Seabass Pro

www.anatomicsitt.com  | +46 11 16 18 00

Footrest

Mounting of footrest 

No matter the variant of footrests, mounting is the same.
Insert the footrest attachment (A) into the intended holes under the front part of 
the seat plate. Tighten the screws (B) on both sides. 

Adjusting the angle of the knee-joint

Loosen the levers (D) slightly and adjust the footrest to the desired angle. Tighten 
the levers.

Adjusting the height of the footrest

Release the levers (E) slightly and adjust the footrest to the desired height. Tighten 
the levers.

Safety stop 

Safety stop (C) in the form of a rail pin is mounted in the bottom of footrest profile. 
The safety stop (C) can also be used to find back to a preset height position.

Note! 

  

Remove the profile stop from the footrest attachment on the 

 

 front of the seatplate before mounting the footrests.

Note! 

  

Install an additional safety stop above the footrest in the track 

 

 of the footrest profile.

Summary of Contents for Zitzi Seabass Pro

























































Reviews:

No comments