manualshive.com logo in svg

Anatomic SITT Zitzi Seabass Pro, User Manual, Page: 26 / 56

Share
Download
Anatomic SITT Zitzi Seabass Pro User Manual Download Page 26

26

User manual  Zitzi Seabass Pro

www.anatomicsitt.com  | +46 11 16 18 00

Brakes

Using drum brake 

The chassis is equipped with drum brakes that can be activated by the attendant. 
Always check that the brakes are working properly before use.
 
Press the right brakehandle (A) while pusching the wheelchair forward. 
The rear wheel shall brake and stop spinning. The brakehandle (A) should not be 
possible to press all the way to the driving handle. About 5-10 mm’s should remain 
when brakes are set.

Repeat the procedure with the left brakehandle.

Setting the brakes 

To activate locking of a wheel, press the brakehandle (A) and push the red locking 
device (B) forward.

Releasing the brakes

To release locking of a wheel, press the brakehandle (A) and the locking device (B) 
will release automatically. Then let go of the brakehandle (A).

If the brakes does not work

First check the tension of both brakewires. If a wire has low tension, try to tens it by 
loosen the screw (C) and then tighten again. If the adjustment is not enough try the 
following quick-setup guide to re-tighten the brake cables.

1.  Tighten the screw (C) to its bottom position
2.  Loosen the nut (D)
3.  Squeeze the brake by lifting the drum brake arm (E) and move the nut (D)    
 

further up the wire.

4.  Tighten the nut (D) and adjust the tension with the screw (C).

Summary of Contents for Zitzi Seabass Pro

























































Reviews:

No comments