Anapol EU-50 Operating Instructions And Equipment Description Download Page 36 | Manualshive

Page: 36 / 41

Anapol EU-50 Operating Instructions And Equipment Description Download Page 36

Page 36

10.1

Jobs to be done during an inspection

PARTS WORK

DONE

DESCRIPTION

PERIODS

CO SENSOR FILTER

Replaced

If present

1 YEAR

NO SENSOR FILTER

Replaced

If present

1 YEAR

THREE-WAY FILTER

Replaced

1 YEAR

WATER SEPARATOR SEAL

Replaced

Silicon seal

1 YEAR

SILICON HOSES

Replaced

All hoses

1 YEAR

INSULATION HOSE PROBE

Replaced

1 YEAR

CPU BATTERY

Replaced

RTC clock

3 YEARS

NO BATTERY

Replaced

2 YEARS

CALIBRATION OF ALL SENSORS AND

GENERAL FUNCTION CONTROL

Carried out

1 YEAR

SOFTWARE

Programmed

Last version

CLEANING

Carried out

1 YEAR

10.2

EMC conformity

Notes on EMC conformity:

The perturbing electromagnetic radiation emitted lies well below the legal limit value.
High voltage discharges on plastic parts (front panel) have no effects. Discharges on metal parts
(connections, probes) can initiate a restart (reset) of the device.
Strong high frequency fields (several watts) in the immediate vicinity of the device (~50cm) can lead to a
disturbance in measured values.
The source of the interference should be removed (e.g. mobile telephone).

«
...
34
35
36
37
38
...
»

Summary of Contents for EU-50










































Reviews:

No comments