CENTRIX™ & EVENTIX™
Chapter 5 : USING FRAME STORE AND LOGO INSERTION (continued)
PAGE 41
5-3. USING LOGO INSERTION WITH THE REMOTE KEYPAD OR EVENTIX
™
This function allows storing up to 8 logos in order to incrust them into the displayed image (up to 2 logos at a same time).
IMPORTANT
: The output format used when displaying logo should be the same that the output format used during the
logo storing.
5-3-1. HOW TO STORE A LOGO
c
Select the source of the logo to be stored (with the INPUT SELECTION buttons).
d
Select the
MAIN
or
PREVIEW
record logo
mode (
LOGOS/FRAME > record logo > MAIN or PREVIEW
):
the device displays a white rectangle corresponding to the logo selection area onto the output. Then adjust the
position and size of the logo selection area with the LCD
record
logo
menu functions.
NOTE:
The logo area is limited to an eighth (1/8) of the displayed area.
e
If necessary, adjust the
luma key
level (
LOGOS/FRAME > record logo > MAIN or PREVIEW > luma key
level
). This function allows to "erasing" the darkest portions of the logo selection area in order to make special logo
contour. Otherwise set the
luma key
level to zero.
NOTE:
You can change the color of the "erased portions" of the logo (
LOGOS/FRAME > record logo > back.
color
).
f
Store the logo into a memory (
LOGOS/FRAME > record logo > MAIN or PREVIEW > store > empty or logo
x
). The memorization of the logo starts and will take about few seconds.
NOTE:
Renew the steps
c
to
f
to store another logo (up to 8).
5-3-2. HOW TO ASSIGN A LOGO
NOTE:
You can assign the stored logos to one or many of the 8 inputs (up to 2 logos by inputs).
g
In the
assignment
menu (
LOGOS/FRAME > use logo/frame > assignment
), select the displayed input (MAIN or
PREVIEW) that you want to assign a logo, then select an index (
1
or
2
) and finally select the needed logo.
NOTE:
To remove a logo from an input, select the corresponding input & index and select
none
.
NOTE:
To assign the same logo to all inputs select
ALL
(instead MAIN or PREVIEW).
h
With the
INPUT SELECTION
buttons, display successively all your inputs to verify your logo assignment. If no
logo appears on an input: verify that the LCD
display
function of the corresponding input is not set to the
OFF
position. In this case press
ENTER
to set it to the
ON
position (See how to display OFF or ON a logo).
5-3-3. HOW TO DISPLAY OFF or ON A LOGO
i
To display OFF or ON the assigned logos of an input, select the MAIN or PREVIEW displayed input in the
display
menu (
LOGOS/FRAME > use logo/frame > display > MAIN or PREVIEW
) and press
ENTER
to change the
status (ON or OFF).
NOTE:
When displaying ON or OFF a logo, this one appears/disappears with a fade effect. You can adjust the
duration of this fade effect (
LOGOS/FRAME > use logo/frame > fade duration
).
5-3-4. HOW TO ADJUST THE LOGO POSITION
j
Press the MAIN / OUTPUT 1 key or the PREVIEW / OUTPUT 2 key.
k
Press the LOGO position key. Then adjust the logo position with the H &V position functions.
NOTE:
When you are using 2 logos by input, make sure to not superpose a logo onto an other one. In case of
superposition, the logo areas will appear colored.
5-3-5. EXAMPLE OF LOGO INSERTION
Figure 37
Logo
source
Video source
Video source with inserted logo.
(white border = logo area)
(logo made with luma key)
www.liveline.be
Summary of Contents for CentriX CTX8022
Page 2: ...www liveline be ...
