![background image](http://html1.mh-extra.com/html/amx/modero-nxd-cv5/modero-nxd-cv5_operation-reference-manual_2938958041.webp)
Configuring Communication
35
5" Modero Widescreen Touch Panel
Configuring and Using USB with a Virtual Master
NetLinx Studio can be setup to run a Virtual Master where the PC acts as the Master by supplying its
own IP Address for communication to the panel. The PC is first equipped with the USB driver, the panel
is then configured for USB communication, and then Studio is configured to act as the Master.
For a personal computer to establish a connection to a Modero panel via USB, the target computer must
have the appropriate AMX USB driver installed. This installation is bundled into the latest TPDesign4
software setup process or can be downloaded independently from the main Application Files page on
www.amx.com
.
Step 1: Setup the Panel and PC for USB Communication
1.
If you do not currently have the latest version of TPDesign4, navigate to
www.amx.com
>
Tech
Center
>
Downloadable Files
>
Application Files
>
NetLinx Design Tools
section of the website
and locate the AMX USB Driver executable (
AMX USBLAN Setup exe
).
2.
Download this executable file to a known location on your computer.
3.
Launch the Setup.exe and follow the on-screen prompts to complete the installation.
Step 2: Confirm the Installation of the USB Driver on the PC
The first time each AMX touch panel is connected to the PC it is detected as a new hardware device and
the USBLAN driver becomes associated with it (
panel specific
). Each time thereafter the panel is
"recognized" as a unique USBLAN device and the association to the driver is done in the background.
When the panel is detected for the
first time
some user intervention is required during the association
between panel and driver.
1.
After the installation of the USB driver has been completed, confirm the proper installation of the
large Type-A USB connector to the PC's USB port, and restart your machine.
2.
Connect the terminal end of the 12 VDC-compliant power supply cable to the power connector on
the rear/side of the touch panel and then apply power.
3.
After the CV5 panel powers-up, press and hold the grey Front Setup Access button (
for 3 seconds
)
to continue with the setup process and proceed to the Setup page.
4.
Select
Protected Setup
>
System Connection
(located on the lower-left) to open the System
Connection page (FIG. 33).
5.
Toggle the blue
Type
field (
from the Master Connection section
) until the choice cycles to
USB
.
Refer to the
System Settings Page
section on page 74 for more information about the fields on this
page.
It is recommended that firmware KIT files only be transferred over a direct connection
and only when the panel is connected to a power supply. I
The mini-USB connector
MUST
be plugged into an already active panel before the
PC can recognize the connection and assign an appropriate USB driver. This driver is
part of both the NetLinx Studio and TPDesign4 software application installations.
If the panel is already powered, continue with steps 3.
The panel MUST be powered and configured for USB communication before
connecting the mini-USB connector to the panel’s Program Port.
Summary of Contents for Modero NXD-CV5
