background image

Page 3 of 4

Liquid soap refill only

(Solo jabon de liquido)

Liquid soap refill only

(Solo jabon de liquido)

www.amtcorporation.com

Reset Button

Press and hold for 7 seconds to prime soap
(Aprete y sostenga por 7 segundos para subir el jabon)

Liquid soap refill only

(Solo jabon de liquido)

Reset Button

www.amtcorporation.com

Reset Button

Press and hold for 7 seconds to prime soap
(Aprete y sostenga por 7 segundos para subir el jabon)

1. Flashing Red LED Indicates Low Soap

2. Unscrew Liquid Soap Bottle

   

3. Refill Liquid Soap Bottle
       

4. Re-install Liquid Soap Bottle   

5. Press and Hold Reset Button for 7 Seconds to 
    Prime New Soap and Reset Flashing Red LED.   

Refill Soap When Soap Level is Approx. 3/4” (20mm)

3/8”

(10mm)

www.amtcorporation.com

Reset Button

Press and hold for 7 seconds to prime soap
(Aprete y sostenga por 7 segundos para subir el jabon)

Liquid soap refill only

(Solo jabon de liquido)

Flashing Red LED

3/4”

(20mm)

Max Filling Level is

 Approx. 3/8” (10mm) 

From Top of Bottle

Troubleshooting:

Flashing BLUE LED

Flashing RED LED

Problem

Solution

Batteries are low/drained. Replace all 4 batteries (D-size).

Soap is low or empty. Refill soap bottle and press and hold reset button for 7 seconds to prime new soap and reset LED.

Soap does not come out of spout

Spout filter is dirty and won’t pump soap through the spout. Clean or replace spout filter assembly.  

Soap Refill Instructions:

Soap dispenses very weak 

Wrong soap was used and pump is dirty. Refill soap bottle with water and press and hold reset button for 7 seconds to 
prime water through the unit. This should be repeated until only water dispenses and soap is completely flushed out. 
Once unit is flushed out, refill soap bottle with liquid soap. Prime unit again until soap comes out. 

*Viscosity Range: (mPa•s or Cp): 100-3800
  pH Range: 5.0 - 9.0

*Failure to use soap products within the 
 required range of viscosity and pH may 
 result in damage to product and void 
 warranty.

Important: Use low viscosity liquid hand soap
                   with no abrasives.

ASD-400 LIQUIDFLO™ 

AUTOMATIC LIQUID SOAP DISPENSER 

INSTALLATION & OPERATION MANUAL

Summary of Contents for Liquidflo ASD-400

Page 1: ... to pump through the spout In some cases there may be some trapped air in the system that does not allow the soap to initially prime If this is the case you will need to blow through the soap filter to clear the trapped air Then prime the soap again The soap should now prime through the spout For further assistance please call Technical Support at 1 800 874 7822 IMPORTANT PRE INSTALLATION NOTE Soa...

Page 2: ... and pH may result in damage to product and void warranty 6 Screw soap bottle onto soap bottle coupler and hand tighten 7 Connect sensor cable onto battery pack you will hear pumps and soap will purge for approximately 5 seconds 8 Soap dispenser is now ready for use Soap Bottle Coupler Threaded Stem Low Battery Indicator Low Soap Indicator Flashing BLUE LED Flashing RED LED Liquid soap refill only...

Page 3: ...el is Approx 3 8 10mm From Top of Bottle Troubleshooting Flashing BLUE LED Flashing RED LED Problem Solution Batteries are low drained Replace all 4 batteries D size Soap is low or empty Refill soap bottle and press and hold reset button for 7 seconds to prime new soap and reset LED Soap does not come out of spout Spout filter is dirty and won t pump soap through the spout Clean or replace spout f...

Page 4: ...ACE OR REPAIR DEFECTIVE PRODUCT AT NO CHARGE CLAIMS FOR LABOR TRANSPORTATION AND ANY OTHER INCIDENTAL COSTS WILL NOT BE ALLOWED AMTC WILL NOT BE RESPONSIBLE FOR ANY CONSIDERABLE DAMAGES OF ANY KIND WHATSOEVER FOR TECHNICAL SUPPORT PLEASE CALL TOLL FREE 1 800 874 7822 OR VISIT OUR WEBSITE AT WWW AMTCORPORATION COM MAKE SURE TO VISIT OUR WEBSITE PERIODICALLY FOR INFORMATION ON NEW PRODUCTS AND TO DO...

Reviews: