Amptec Research 720A Operation And Maintenance Manual Download Page 26

Page: 26 / 27

720A Operation and Maintenance Manual – Rev S – January 25, 2019

Page 26

13231 Rooster Springs Rd.,

Austin, TX 78737

(512) 858-4045

[email protected]

amptec.com

Precision Standard Resistors Continued:

•

One 100 KΩ resistance standard at ± 0.005% or better accuracy

Other Equipment:

•

One trimmer potentiometer adjustment tool

•

One AMPTEC OP-300 48” gold plated Kelvin clip lead set

•

(Optional) One AMPTEC OP-304 48” banana jack calibration lead set

E-4.2 Trimmer Potentiometer Adjustment Locations

The locations of the trimmer potentiometers (referred to as trim pots in this procedure)

that you will adjust during calibration are shown on

Figure 9

below. You will be using the

trim pots that are located at RV1, RV2, RV5, and RV6 to calibrate your instrument.

Figure 9

Trim Pot Locations on Main Board of 720A Meter

Summary of Contents for 720A




























Search results

Summary of Contents for 720A

Reviews:

Related manuals for 720A

Brands by name

Popular brands

Amptec Research 720A, Operation And Maintenance Manual

Search results

Summary of Contents for 720A

Reviews:

Related manuals for 720A

Brands by name

Popular brands