Amptec Research 720A Operation And Maintenance Manual Download Page 20

Page: 20 / 27

720A Operation and Maintenance Manual – Rev S – January 25, 2019

Page 20

13231 Rooster Springs Rd.,

Austin, TX 78737

(512) 858-4045

[email protected]

amptec.com

Deselects all ranges.

Selects the 200 m

Ω

range.

Selects the 2

Ω

range.

Selects the 20

Ω

range.

Selects the 200

Ω

range.

Selects the 2 K

Ω

range.

Selects the 20 K

Ω

range.

Selects the 200 K

Ω

range.

Data Format

The RS-232C Interface outputs reading data in the following format:

1.2345

E+4

The measurement is always in ohms and the number following “E” is the

exponent multiplier. For example, 1.2345E+4 is equal to 12.345 K

Ω

Range

Exponent

200 m

Ω

E-1

Ω

E+0

Ω

E+1

200

Ω

E+2

2 K

Ω

E+3

20 K

Ω

E+4

200 K

Ω

E+5

Please note that an overrange reading will be indicated by 9.9999E<pn>, where p is the

polarity of the exponent and n is the multiplier of the range. The range exponents are

listed above.

Summary of Contents for 720A




























Search results

Summary of Contents for 720A

Reviews:

Related manuals for 720A

Brands by name

Popular brands

Amptec Research 720A, Operation And Maintenance Manual

Search results

Summary of Contents for 720A

Reviews:

Related manuals for 720A

Brands by name

Popular brands