manualshive.com logo in svg

Amprobe AM-140, User Manual, Page: 8 / 20

Share
Download
Amprobe AM-140 User Manual Download Page 8

 

7 

  Hz Logic Level Frequency and % Duty Cycle functions 

Press 

SELECT

 button momentarily to toggle between Hz and % (duty cycle) readings. 

The new setting will be saved automatically to the non-volatile memory as power up 
default. Press 

500000 

button momentarily to toggle between 5 full digits and 6 full digits 

Hz readings. 

 

 

 

Note: Unlike the Line Level Frequency measuring function as previously stated, this 

Logic Level Frequency function is set only at the highest input sensitivity to measure 

digital type electronic signals. 

 
T1-T2 Dual Channels Temperature function (AM-160 only) 

Press 

SELECT

 button momentarily to toggle between 

°

C and 

°

F readings, and the 

new setting will be saved automatically in the non-volatile memory as power up default. 

Press T1-T2 (

RANGE

) button momentarily to select T1, T2, or T1-T2 readings. 

 

Note: Insert the banana plug K-type temperature bead probe Bkp60 (standard 
accessory x 1) with correct 

  polarities. Dual channels T1-T2 readings require 2 

probes. You can also use a plug adapter Bkb32 (Optional purchase) with banana pins 

to K-type socket to adapt other standard K type mini plug temperature probes.   

Summary of Contents for AM-140





















Reviews:

No comments