Amprobe AM-140 User Manual Download Page 10 | Manualshive

Page: 10 / 20

Amprobe AM-140 User Manual Download Page 10

9

CAUTION

Using resistance or continuity function in a live circuit will produce false results and
may damage the meter. In many cases the suspected component must be

disconnected from the circuit to obtain an accurate reading.

Capacitance,

Diode test function

Press

SELECT

button momentarily to toggle between Capacitance and

Diode Diode test functions. The new setting will be saved automatically to the

non-volatile memory as power up default.

CAUTION

Discharge capacitors before making any measurement. Large value capacitors should

be discharged through an appropriate resistance load.

Note: Normal forward voltage drop (forward biased) for a good silicon diode is between
0.400V to 0.900V. A reading higher than that indicates a leaky diode (defective). A zero

reading indicates a shorted diode (defective). An OL indicates an open diode

(defective). Reverse the test leads connections (reverse biased) across the diode. The

digital display shows OL if the diode is good. Any other readings indicate the diode is
resistive or shorted (defective).

«
...
8
9
10
11
12
...
»

Summary of Contents for AM-140





















Reviews:

No comments